M002U
WARNING
！
！
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIP OVER.
SMALL PARTS- NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual.
Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect
assembly or inappropriate use.
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
VESA Plate
e (x2)
Swivel Arm
d (x1)
C-Clamp
b (x1)
C-Clamp Brace
c (x1)
Pole
a (x1)
Wire Clip
n2 (x4)
Wire Clip
n1 (x1)
Grommet Base Plate
m (x1)
M4 Spacer
s (x8)
M8x12 Bolt
g (x2)
Nut
h (x2)
M5x14 Bolt
f (x3)
Wrench
p (x1)
Allen Key
o (x1)
M4x30 Bolt
r (x8)
M4x12 Bolt
q (x8)
M10 Bolt
i (x1)
Support Plate
j (x1)
M10 Washer
k (x1)
Spring Washer
l (x1)
INSTALLATION MANUAL
1-844-SATTLER (18447288537)
www.walielectric.com
TIPOVER WARNING
RT OF MONITOR OR STAND.
Supplied Parts List
Dual Monitor Desk Mount
with Bracket Adapter
(x8) (x1)
E
(x8)
D
Bracket
①
(x4)
Connector
②
(x4)
Cover
③
(x4)
M6X80
A (x4)
M6X60
B (x4)
M6X40
C (x4)
Option A : Clamp Installation
1
a
c
f
o
Connect Pole a and C-Clamp Brace c from the bottom using M5x14 Bolt f and tighten with
Allen Key 3mm o .
Select the preferred height according to your desk thickness. Connect C-Clamp b to C-Clamp
Brace c using M8x12 Bolt g and tighten with Allen Key 5mm o . Rotate the hand knob
clockwise to fasten for stability.
c
o
g
b
a
c
f
o
Hand Knob
c
o
g
b
o
a
m
f
Option B : Grommet Base Installation
1.
Place Pole a onto Grommet Base Plate m . Connect
them from the bottom using M5x14 f
Bolt and tighten
with Allen Key 3mm o .
o
a
m
f
p
p
2a. Existing Grommet Hole Installation
2b. Self-drilled Grommet Hole Installation
If the existing grommet hole comes with a plastic protector, remove it to ensure a flat
surface before installing the desk mount. Position the Pole a on the mounting surface
and secure using the Support Plate j , M10 Washer k , Spring Washer l , and M10
Bolt i . Fasten the Bolt using the provided Wrench p .
p
j
k
l
i
a
Mark the position of the hole on your mounting surface. Drill a 3/8" (10mm) diameter hole
at the marked position through the mounting surface. Position the Pole a on the mounting
surface and secure using the Support Plate j , M10 Washer k , Spring Washer l , and
M10 Bolt i . Fasten the Bolt using the provided Wrench p .
a
j
k
l
p
i
ø 10mm
(ø ")
3/8
j
k
l
i
a
j
k
l
i
a
x2
