Wainman Hawaii ManiaC Скачать руководство пользователя страница 5

FRONT LINE ATTAchMENT

www.wainmanhawaii.com  -  3

There are 3 trimming options on the front lines called the “Feeling Spectrum” which gives you options of aggressive vs. relaxed, 
upwind vs downwind, lower vs higher bar pressure, fast turning vs wider turnsIt is suggested that the ManiaCs be used on the 
factory “upwind” setting for the first few sessions. This “upwind” setting is the configuration that comes straight out of the bag 
when you purchase the kite . It is very important to properly trim the kite (on the clam cleat). If the kite is not properly trimmed, 
the performance of the kite may be jeopardized (back stalling etc.). When you decide it is time for changing the ManiaC 
performance characteristics, it is suggested that you always make a single change at a time (on center and back lines). This 
approach will enable the rider to find his/her perfect setting to match their riding style and maximize optimal performance. 

REMEMBER: 

When changing the front line setting, be sure to adjust the knot to the corresponding setting on the pigtail. 

UPWIND tab on LE / UPWIND knot on LE pigtail; DOWNWIND tab on LE / DOWNWIND knot on LE pigtail; “STOCK” tab on LE / 

“STOCK” center knot on LE pigtail (“STOCK” is not labelled on kite). 

“MOdERATE" sETTINg

Attach LE pigtail to STOCK (middle tab not labeled) 
tab on LE (see diagram on left). The center lines 
attaches to a LE pigtail with 3 knots (see diagram on 
right) on it: UPWIND which is labeled, “MODERATE” 
which is the center knot and not labeled, DOWNWIND 
which is labeled. The “MODERATE” setting is the 
all- round setting. You can adjust the pigtail to 
find your favorite riding characteristic for the kite.  
To change the settings, undo larks head knot on LE 
pigtail. Remove LE pigtail and attach to desired tab 
(UPWIND or DOWNWIND). 

dOwNwINd sETTINg

Attach LE pigtail to DOWNWIND tab on LE (see diagram 
on left) . Attach larks head knot to DOWNWIND knot 
(see diagram on right) on LE pigtail that is labeled on 
the kite. This option will make the kite shift back into 
the window increasing downwind riding. The kite will 
turn faster and jump with a more horizontal lift. The 
kite sits deeper (further back) in the window and the 
bar pressure decreases. 

UPwINd sETTINg

The ManiaC comes set up on the “UPWIND” setting tab 
on the LE out the bag using the END tab and knots (see 
diagram on left and right). This  option will make the 
kite shift further towards the edge of the wind window 
enabling better upwind capabilities. The kite will turn 
a bit slower than the “STOCK” setting and jump with 
a traditional vertical lift. This setting will also have 
increased bar pressure. 

Содержание ManiaC





























Отзывы: