background image

 

249.805.013 

32 

Date: 2021-12-09

 

 

10 

INV NOT ENABLED 

Inverter  enable  signal  missing  at  the  control 
terminal rail, terminal 3. 

The inverter can only be started if an active enabling signal (12-15 V) is applied to the 
control terminal rail. If this signal fails during drive operations, the motor will shut down 
and coast to a standstill. The shutdown immediately affects the inverter power section. 
 
This signal is provided by an orange wire connected to the number 3 connection on the 
terminal rail in the Roll Down. If this wire is not connected this error will occur.  
 

11 

INV SER TIME OUT 

Shutdown when telegrams fail (serial interface). 

Power cycle the Roll Down. 
Unplug the power and wait 30 seconds before applying power again. 
 

255 

INV SER TIME OUT 

Timer reset of the watchdog. 

Power cycle the Roll Down. 
Unplug the power and wait 30 seconds before applying power again. 
 

12 

INVERTER TIMING 

Internal timing error 

Power cycle the Roll Down. 
Unplug the power and wait 30 seconds before applying power again. 
 

13 

INVERTER SYSTEM 

System error 

Power cycle the Roll Down. 
Unplug the power and wait 30 seconds before applying power again. 
 

14 

INV START DIRECT 

Start attempt with direction error 

Power cycle the Roll Down. 
Unplug the power and wait 30 seconds before applying power again. 
 

15 

INV PROGRAM CRC 

Program memory CRC error 

Power cycle the Roll Down. 
Unplug the power and wait 30 seconds before applying power again. 
 

16 

INV NOT ENABLED 

Inverter enabling signal error 

The inverter can only be started if an active enabling signal (12-15 V) is applied to the 
control terminal rail. If this signal fails during drive operations, the motor will shut down 
and coast to a standstill. The shutdown immediately affects the inverter power section. 
 
This signal is provided by an orange wire connected to the number 3 connection on the 
terminal rail in the Roll Down. If this wire is not connected this error will occur.  
 

17, 250 

INV WATCHDOG RST 

Reset through Watch Dog 

Power cycle the Roll Down. Unplug the power and wait 30 seconds before applying power 
again. 
 

Содержание Roll Down









































Отзывы: