IMPORTANT SAFETY PRECAUTIONS:
Read all instructions carefully before using. When
using an electrical appliance, basic precautions
should always be followed, including the following:
DANGER
To reduce the risk of death or injury by electric
shock:
1. Do not reach for the Shaver/Shaper, after it has
fallen into water. Unplug immediately.
2. Do not use while bathing or in a shower.
3. Do not place or store the Shaver/Shaper where it
can fall or be pulled into a tub or sink. Do not place
or drop into water or liquid.
4. Always unplug the unit from the electrical
outlet, immediately after using.
5. Unplug unit before cleaning.
WARNING
To reduce the risk of burns, fire, electric shock
or injury to persons:
1. This appliance is not suitable for use by people
(including children) with physical, sensory or mental
disabilities or who do not have the relevant
experience or knowledge of using such appliance
unless under the supervision of or after having
received instruction in the use of the appliance by an
individual who is responsible for their safety.
Children should be supervised to ensure they do not
play with the appliance.
2. Use the Shaver/Shaper only for it’s intended use,
as described in this manual. Do not use attachments
not recommended by the manufacturer.
3. Never operate if the unit has a damaged cord or
plug, if not working properly, if dropped or
damaged, or if dropped into water. Return your
CLEANING YOUR FOIL/CUTTER BAR
For your system to work properly, it is important
that you begin shaving with blades that are clean
and free of hair and other debris that might effect
performance. It is recommended that you clean
your Shaver/Shaper after every 2 or 3 shaves,
using the cleaning brush, and following the
instructions outlined below.
Shaver/Shaper: Remove the foil head from the top
of your Shaver/Shaper, by pressing the round
button located on the right side of the unit, and
lifting the flex foil head off of the shaver. This will
expose the cutter bar assembly. The flex foil head
may be cleaned of loose material, by gently
tapping it against the surface of your sink. Be
sure your sink is empty, and does not contain any
water in it before you hold your Shaver/Shaper
over it. Never hold any electrical appliance over
any container that has water in it, as it may fall
into the water and cause severe electrical
shock. Remove any loose hair and debris from
the cutter bar assembly and surrounding area, by
brushing it away gently with your cleaning brush.
Then, remove the cutting bar, by gently pressing
down on it, and turning it 90 degrees. It should
pop right off. Run the cutter bar under some
warm water, and dry it off with a paper towel.
Return it to the shaver by reversing this process,
and replacing the foil head. By properly cleaning
and maintaining your Shaver/Shaper it will
provide maximum comfort and bump-free
shaving.
AFTER SHAVING:
Wash your face with soap
and warm water, and apply any talc or after-shave
lotion of your preference.
TIPS FOR FIRST-TIME USERS:
If you are using an electric shaver for the first time,
your skin will probably need to condition itself to this
new shaving technique. Always shave with a light
touch and use your Wahl Shaver/Shaper exclusively
for three to four weeks, or longer if you have sensitive
skin or if your whiskers grow at different angles in
certain areas. Initially, your shaves may not be as close
as you would like. But, stick with it, and you will
eventually get the great shave you are looking for. If
you have been using another type of electric shaver
before, there may be a period of conditioning, before
you receive maximum results from the Shaver/Shaper.
CUSTOM SHAVING
We suggest that you thoroughly cleanse and
completely dry your skin prior to shaving.
Provided your beard is no longer than 1/32”, begin
shaving at the neckline, in short, upwards strokes,
and then continuing upwards, until you have shaved
all areas of your beard, as you desire. The Shaver/
Shaper is especially designed to remove most facial
hair, and give you a close, clean shave, that is bump
and irritation free. Do not press hard against the
skin, but allow the shaver to work for you. The
results should provide you with the closest shave
possible, without bumps or irritation.
For those times when your beard is longer than
1/32”, begin by using a trimmer, to cut your beard,
then use the Shaver/Shaper to get a close, clean
shave. The foil head of the Shaver/Shaper is
especially designed for “bump-free shaving “and will
not feed hair into the cutter bar, that is longer than
1/32”.
(As a general rule, we recommend replacing the Flex
Foil Head every six months for maximum results.
The foil is micro-thin with precise, raised inner
cutting edges around the whisker holes. These
raised cutting edges will wear with use, which will
be indicated if your shaver slows down and the
blades seem to get warm. Always replace the Foil
Guard to protect the delicate dual foil heads when
the shaver is not in use. To ensure continued
shaving satisfaction, you should replace the foils
often and cutter bar periodically. We recommend foil
replacement twice a year. Cutters should be replaced
at least every two years.)
CHARGING OPERATION
The Shaver/Shaper can be used with a cord, or
without the cord if adequately charged. Unlike many
other shavers, you will have the ability to shave even
if the battery power is low.
·For best performance, charge for 18 hours before
the first shave.
This product has been designed with the charger in
the plug. This construction allows the shaver to be
very powerful yet much lighter for easier
maneuverability, and it also keeps the line voltage
safely at the plug, and not in the shaver.
·Plug the transformer cord into the shaver. BE SURE
SHAVER IS IN THE “OFF” POSITION, (MARKED “O”
ON THE SHAVER) WHEN CHARGING, except when
the unit is running.
·In the “off” position, the Recharging Indicator Light
will glow whenever the shaver is connected to an AC
power supply. (If might take a minute or two for the
LED indicator to glow, if the battery is fully
discharged.) The shaver cannot be overcharged, so
you may charge it as often as desired. However,
periodic recharging of the shaver, rather than
continuous recharging, will prolong the battery life.
CORD CARE
The cord should never be used to pull the Shaver/
Shaper. Freedom of movement needs to be
maintained. Care should be used to keep the cord
untwisted, and undamaged.
When stored, the cord should be coiled and placed
neatly in a dry place.
Shaver/Shaper to Wahl Clipper Corporation for
examination & repair.
4. Keep the appliance dry
5. Keep the cord away from heated surfaces.
6. Never drop or insert any object into any opening.
7. Do not use outdoors or operate where aerosol
(spray) products are being used or where oxygen is
being administered.
8. Do not use this Shaver/Shaper with a damaged or
broken foil, as facial injury may occur.
9. Always attach plug to appliance first, then to the
outlet. To disconnect, turn all control to “off”, and
then remove plug from outlet.
10. Use only the charger supplied by the
manufacturer to recharge this shaver.
SAVE THESE INSTRUCTIONS
THIS PRODUCT IS DESIGNED FOR COMMERCIAL
USE ONLY.
Disposal/Replacement of
Ni-cad battery
CONTAINS SEALED, RECHARGEABLE
NICKEL-CADMIUM BATTERY. MUST
BE RECYCLED OR DISPOSED OF
PROPERLY.
Depending on use, your battery in the Shaver/Shaper
should last four to six years before replacement is
necessary. When replacement is necessary, follow
these simple steps:
1.First remove the Flex Foil Head. Next remove the
Cutter Bar Assembly by gently pressing down, and
turning the bar 90 degrees.
2.Remove the two Spring Clips on the top of the
shaver using a small, flat-blade screwdriver. Place
hand over Spring Clips when removing in order to
prevent the clips from springing away and getting
lost. Pull back the housing away from the shaver.
3.Remove the old battery from the shaver (pry
cement loose).
4.Insert replacement battery (Wahl Part #0745-302),
available from Wahl Clipper Corporation
(815) 625-6525.
5.Assemble the shaver housing. Be sure rubber
gasket is located properly, and snap Spring Clips
back in place.
6.Return the Cutter Bar Assembly and Flex Foil Head.
7.For proper disposal, call 1-800-8 BATTERY for a
recycling center in your area.
QUICK TIPS & HANDY REMINDERS
1.If you are a first-time electric shaver user, or
changing from another brand, there will be a 2-3
week (or less) adjustment period, while your face and
beard adapt to the new foil.
2.When you open your package, charge your shaver
for 18 hours before the first shave.
3.Replace the foil every 6-12 months, depending on
how often you shave and how tough your beard is.
4.Be sure to clean the shaver, cutter bar and foil
every two or three shaves.
5.Replace the cutter bar every 12-18 months.
6.Keep using and your face and beard will adapt to
the shaver.
7.During the break-in period of the cutter bar, you
may experience a black residue left on the face. It is
a harmless combination of whiskers, skin debris and
minute particles from the cutter bar, which will wash
off easily. This condition will quickly disappear with
use.
8061 5-STAR SHAVER
Operating Manual
Manual de Operación
Manual d’ Utilisation
LIMITED 1 (ONE) YEAR WARRANTY
(Valid in U.S.A. Only)
If your Wahl product fails to operate satisfactorily
within one (1) year from the date of original
purchase or receipt as a gift, Wahl will at our
option repair or replace it and return it to you
FREE OF CHARGE. Our warranty does not cover
blades which are wear out parts. Please mail your
product prepaid to Wahl Clipper Corporation,
3100 N. Locust St., Sterling, Illinois 61081,
Attention: Repair Department, with a note
describing the defect and the date of original
purchase or receipt as a gift (if in warranty).
Products out of warranty will be repaired at our
standard repair charges.
This warranty is void and no repair or
replacement will be made under this warranty or
otherwise if:
1. The product is modified in any manner.
2. The product is repaired by anyone other than
Wahl Clipper Corporation
3. The product has been subject to unreasonable
use.
This warranty gives you specific legal rights and
you may also have other rights which may vary
from state to state. No other written express
warranty is given. Any implied warranty including
any warranty of merchantability, which may arise
from purchase or use is limited to the one-year
period provided in this express warranty. Some
states may not allow such limitation, so it may
not apply to you. No responsibility is assumed for
incidental or consequential damages of any type,
or for the use of unauthorized attachments. Some
states may not allow the exclusion or limitation of
incidental or consequential damages, so the
limitation or exclusion may not apply to you.
Warranty valid only in the United States.
GARANTIA LIMITADA POR UN (1)
AÑO
(Válida solo en los Estados Unidos)
Si su producto no llegará a opera satisfactoriamente
en el período de un (1) año, desde . fecha de la
compra original o de haberlo recibido como regalo,
Wahl lo reparará o reemplazará . a su criterio y se lo
enviará GRATU ITAMENTE Nuestra garantía no
cubre las hojas, las cuales son partes deszastables.
Por favor envíe su producto con íranqueo pagado a
Wahl Clipper Corporation, 3100 N. Locust St.,
Sterling, Illinois 61031, Atención: Departamento de
reparaciónes, con una nota describiendo el defecto
y con el recibo de compra original o el recibo como
regalo (si aún está bajo garatiría). Los productos
fuera de garantía serán reparados a nuestros
precios originales de reparación.
Esta garantía no es válida y no se hara ninguna
reparación o reemplazo si el producto:
1. Ha sido modificado en cualquier manera.
2. Ha sido reparado por otro que no sea Wahl
Clipper Corporation .
3. Ha sido sometido a una utilización inadecuada.
Esta garantía le brinda derechos legales específicos
y usted puede adquirir otros derechos, los cuales
varían de un estado a otro. No se brinda ninguna
otra zarantía expresa. Cualguier garanúa implícita
incluyendo cualguier guaratía mercantil la al podria
surgir por la compra ola utilización, está limitada al
período de un año
proporcionado en esta garantía expresa. Algunos
estados no
permihrán tal limitación; por o tanto tal vez no se
aplique a usted. No se asumirá ninguna respons.
abilidad por daños accidentales o consiguientes de
cualquier tipo o por la utilización de dispositivos no
autorizados. Algunos estados no permitirán tal
exclusión o limitación; por lo tanto tal vez no se
aplique a usted. Garantía válida solamente en
Estados Unidos de Norteamérica.
GARANTIE LIMITÉE D’UN AN
Si le produit Wahl cesse de fonctionner de façon
satisfaisante en deçà d’un an, à compter de la
date d’achat initiale ou de réception en cadeau,
Wahl s’engage, à son gré, à le réparer ou à le
remplacer, et à le retourner SANS FRAIS à
l’expéditeur. La garantie ne couvre pas les lames,
les brosses ou d’autres pièces d’usure. Le produit
défectueux doit être envoyé, port payé, à Wahl
Clipper Corporation, 3100 N. Locust St., Sterling,
Illinois 61081, Attention: Repair Department,
accompagné d’une note décrivant le défaut et
indiquant la date d’achat initiale ou de réception
en cadeau (s’il est couvert par la garantie). Le
produit non couvert par la garantie est réparé
moyennant des frais de réparation standard.
La présente garantie est nulle et non avenue, et
aucune réparation ni aucun remplacement ne sont
effectués, au titre de la présente garantie, ou
autrement si :
1) le produit a été modifié de quelque manière
que ce soit;
2) le produit a été réparé par toute entité autre
que Wahl Clipper Corporation;
3) le produit a été soumis à un usage abusif.
La garantie confère à l’acheteur des droits
juridiques précis, qui peut également se prévaloir
d’autres droits propres à son État de résidence.
Aucune autre garantie expresse écrite n’est
donnée. Toute garantie implicite, y compris toute
garantie de qualité marchande, découlant de
l’achat ou de l’utilisation se limite à une période
d’un an, qui est prévue dans la présente garantie
expresse. Certains États peuvent ne pas
reconnaître la présente garantie limitée, qui alors
peut ne pas s’appliquer à l’acheteur. La société
décline toute responsabilité à l’égard de
dommages accessoires ou consécutifs, quels
qu’ils soient, ou de l’utilisation d’accessoires non
approuvés. Certains États peuvent ne pas
permettre l’exclusion ou la limitation à l’égard de
dommages accessoires ou consécutifs, et la
limitation ou l’exclusion peut alors ne pas
s’appliquer à l’acheteur. Garantie valide aux États-
Unis seulement.
Form # 94635-001
shaver_ib.indd 1
3/4/13 3:42 PM
