WAGO WAGO-TO-PASS 761 Скачать руководство пользователя страница 7

Страница: 7 / 84

WAGO-TO-PASS® 761

Notes about this Documentation

761-210 Telecontrol Module Compact

Manual

Version 2.0.0

1.3

Symbols

Personal Injury!

Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.

Personal Injury Caused by Electric Current!

Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.

Personal Injury!

Indicates a moderate-risk, potentially hazardous situation which, if not avoided,
could result in death or serious injury.

Personal Injury!

Indicates a low-risk, potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.

Damage to Property!

Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.

Damage to Property Caused by Electrostatic Discharge (ESD)!

Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.

Important Note!

Indicates a potential malfunction which, if not avoided, however, will not result in
damage to property.

Содержание WAGO-TO-PASS 761





















































































Результаты поиска

Содержание WAGO-TO-PASS 761

Отзывы:

Бренды по названию

Популярные бренды

WAGO WAGO-TO-PASS 761, Руководство пользователя

Результаты поиска

Содержание WAGO-TO-PASS 761

Отзывы:

Бренды по названию

Популярные бренды