WAGO TEchDocs 765-4501/0100-0000 Скачать руководство пользователя страница 114

Страница: 114 / 136

765-4501/0100-0000

Commissioning

114

Product manual | Version: 1.1.0
8PORT IOL-A FLD EI DC 24V 2.0A

The following table lists port-specific configuration parameters.

Table 72: Port-Specific Configuration Parameters

Node Name

Node Class

Access Default Description

OverCurrentPin1, Over-
CurrentPin2, OverCur-
rentPin4

Variable

Read

Warning level for current upper limit on pin 1, pin
2 or pin 4; unit: 1 mA

0: monitoring not enabled

UnderCurrentPin1, Un-
derCurrentPin2, Under-
CurrentPin4

Variable

Read

Warning level for current lower limit on pin 1, pin
2 or pin 4; unit: 1 mA

0: monitoring not enabled

10.3.4.1.3 Reading Process Data

The OPC UA server provides nodes with process data. For example, the OPC UA client
can read out the value on pin 2 of a port in the

Pin2ProcessData

node. The path to this

node is:

Root > Object > DeviceSet > [device name] > IOLinkMaster > PortXX

> ProcessData

Note

OPC UA client can only read process output data

The process output data is written by the EtherNet/IP scanner. The OPC UA client can
only read process output data.

The following table lists port-specific process data.

Table 73: Port-Specific Process Data

Node Name

Node Class

Access

Description

Pin2ProcessData

Variable

Read

Process data on pin 2

Pin4ProcessData

Variable

Read

Process data on pin 4

10.3.4.1.4 Reading out Measured Values

The OPC UA server provides nodes with calculated measured values. For example, the
OPC UA client can read out the calculated total current of supply cable 1 in the

SumCur-

rentL

node. The path to this node is:

Root > Object > DeviceSet > [device name] > IOLinkMaster > Diag-

nostics > Current

The following table lists device-specific (calculated) measured values.

Table 74: Device-Specific (Calculated) Measured Values

Node Name

Node Class

Access

Description

SumCurrentL

Variable

Read

Total current in supply cable 1 calculated
from individual measurements; unit: mA

SumCurrentL2

Variable

Read

Total current in supply cable 2 calculated
from individual measurements; unit: mA

MeanTemperature

Variable

Read

Average value for the temperature of the
assembly, calculated from the temperature
values measured individually on the three
chips; unit: °C

Содержание TEchDocs 765-4501/0100-0000









































































































































Результаты поиска

Содержание TEchDocs 765-4501/0100-0000

Отзывы:

Похожие инструкции для TEchDocs 765-4501/0100-0000

Бренды по названию

Популярные бренды

WAGO TEchDocs 765-4501/0100-0000, Руководство пользователя

Результаты поиска

Содержание TEchDocs 765-4501/0100-0000

Отзывы:

Похожие инструкции для TEchDocs 765-4501/0100-0000

Бренды по названию

Популярные бренды