WAGO 750-632 Скачать руководство пользователя страница 60

Страница: 60 / 152

Function Description

WAGO-I/O-SYSTEM 750

750-632 Proportional Valve Module

Manual

Version 1.3.0, valid from FW/HW-Version 01/01

Table 39: Function Block: Nominal Current

Variable

Value

Unit

PA_NOMINAL_CURR 2000

Process value <Current> 5000

0.01%

Target output current

1000

5.5.5

Function Block: Dither Generator

Using this function block causes a reduction of the influence of static friction.

This enables significant reductions in the response threshold and hysteresis. There

are four parameters provided to use for setting this function:

•

#DG_FREQ

•

#DG_AMPL

•

#DG_RAMP_ON

•

#DG_RAMP_OFF

Parameter #DG_FREQ

The frequency of the dither signal can be set using this parameter in a grid from

1 Hz to 250 Hz. The goal is to select the frequency such that the static friction of

the actuator no longer registers.

Basically, the frequency should be set as low as possible until the system

controlled by the valve reacts to the dither signal superimposed on the setpoint

value. Afterwards, the frequency should be incrementally increased until the

system reaction disappears again.

At frequencies that are too low, the actuator in the valve increasingly follows the

dither signal and the valve output becomes more unstable. At frequencies that are

two high, these effects are not as serious; however, the hysteresis can increase

again.

Parameter #DG_AMPL

With this parameter, the amplitude can be specified in a percentage in relation to

the nominal current. Values up to 50% are possible.

In order to effect a reaction of the valve gate:

•

the selected amplitude must be large enough, and

•

the selected frequency must be small enough.

If the selected amplitude is too large, then pulsing in the hydraulic system

becomes noticeable.

Содержание 750-632

























































































































































Результаты поиска

Содержание 750-632

Отзывы:

WAGO 750-632, Руководство пользователя, Страница: 60 / 152

Результаты поиска

Содержание 750-632

Отзывы: