WAGO 750-370 страница 37 Скачать руководство пользователя

Страница: 37 / 222

WAGO-I/O-System 750

System Description

750-370 PROFINET IO Fieldbus Coupler

Manual

Version 2.0.0

Pos: 18.15.42 /Seri e 750 ( WAGO-I/O-SYSTEM)/Systembeschr eibung/Versorgung/Er dung @ 3\mod_1231246555687_21.docx @ 25802 @ 23443 @ 1

3.7

Grounding

3.7.1

Grounding the DIN Rail

3.7.1.1 Framework Assembly

When setting up the framework, the carrier rail must be screwed together with the

electrically conducting cabinet or housing frame. The framework or the housing

must be grounded. The electrical connection is established via the screw. Thus,

the carrier rail is grounded.

Ensure sufficient grounding is provided!

You must take care to ensure the flawless electrical connection between the

carrier rail and the frame or housing in order to guarantee sufficient grounding.

3.7.1.2 Insulated Assembly

Insulated assembly has been achieved when there is constructively no direct

ohmic contact between the cabinet frame or machine parts and the carrier rail.

Here, the earth ground must be set up via an electrical conductor in accordance

with valid national safety regulations.

Recommendation

The optimal setup is a metallic assembly plate with grounding connection which

is electrically conductive linked to the carrier rail.

The separate grounding of the carrier rail can be easily set up with the aid of the

WAGO ground wire terminals.

Table 11: WAGO Ground Wire Terminals

Order No. Description

283-609

1-conductor ground (earth) terminal block make an automatic contact

to the carrier rail; conductor cross section: 0.2 mm² … 16 mm

Note

: Also order the end and intermediate plate (283-320).

Содержание 750-370































































































































































































































Результаты поиска

Содержание 750-370

Отзывы:

Похожие инструкции для 750-370

Бренды по названию

Популярные бренды

WAGO 750-370, Руководство пользователя

Результаты поиска

Содержание 750-370

Отзывы:

Похожие инструкции для 750-370

Бренды по названию

Популярные бренды