WAGO 2857-570/024-001 Скачать руководство пользователя страница 13

Страница: 13 / 120

2857-570/024-001

Properties

Product manual | Version: 2.0.0

3-Phase Power Measurement Module, 1 A

Pos.

Designation

Details

Current measurement inputs for current transformers

Measurement Inputs [

}

14]

Status and error LEDs

Indicators [

}

18]

Memory card slot "μSD"

Memory Card Slot “μSD” for Micro

SD Cards [

}

18]

Voltage measurement inputs

Measurement Inputs [

}

14]

Switch output "DO"

Switch Output "DO” and S0 Interface

[

}

15]

Supply connection "POWER"

Supply Connection "POWER" [

}

17]

Configuration interface "Config"

Configuration interface "Config"

[

}

17]

Figure 2: View from above

Pos.

Designation

Details

Modbus RTU interface "X2 OUT"

Modbus-RTU interface "X1 IN" and

"X2 OUT" [

}

16]

Modbus RTU interface "X1 IN"

Modbus-RTU interface "X1 IN" and

"X2 OUT" [

}

16]

Содержание 2857-570/024-001

























































































































Результаты поиска

Содержание 2857-570/024-001

Отзывы:

WAGO 2857-570/024-001, Руководство пользователя, Страница: 13 / 120

Результаты поиска

Содержание 2857-570/024-001

Отзывы: