manualshive.com logo in svg

WAGO 2857-570/024-001, Руководство пользователя, Страница: 15 / 120

Поделиться
Скачать
WAGO 2857-570/024-001 Скачать руководство пользователя страница 15

2857-570/024-001

Properties

Product manual | Version: 2.0.0

15

3-Phase Power Measurement Module, 1 A

Position

Designation

Connection

Description

1

Test slot for
associated
Push-in
CAGE CLAMP

®

 connection

2

Push-button

Push-button to open the associated
Push-in CAGE CLAMP

®

3

IL1-S1

Current Transformer at L1

Input for current measurement L1

IL1-S2

4

IL2-S1

Current Transformer at L2

Input for current measurement L2

IL2-S2

5

IL3-S1

Current Transformer at L3

Input for current measurement L3

IL3-S2

6

ILN-S1

Current Transformer at N

Input for current measurement N

ILN-S2

Voltage Measurement Inputs

L1 … N – terminals marked accordingly – are the voltage measurement inputs. Up to four
wires of the network to be measured are connected here.

Figure 5: Measurement inputs for voltage measurement

Position

Designation

Connection

Description

1

Test slot for
associated
Push-in
CAGE CLAMP

®

 connection

2

Push-button

Push-button to open the CAGE
CLAMP

®

3

N

N-conductor N

Reference potential for current and
voltage

4

L3

Conductor L3

Input for voltage measurement an L3

5

L2

Conductor L2

Input for voltage measurement an L2

6

L1

Conductor L1

Input for voltage measurement an L1

3.3.2 Switch Output "DO” and S0 Interface

With switch output "DO,” whether the input signal exceeds or falls below the threshold
values can be reported. If it does, the output is set to +24 VDC and delivers a maximum
current of up to 100 mA. Then, e.g., an LED can be actuated.

More detailed information is presented in the following sections:

• "Threshold Over-/Underruns”

Содержание 2857-570/024-001

























































































































Отзывы:

Нет отзывов