WAGNER PROTEC GM 1-350 Скачать руководство пользователя страница 28

28

GM 1-350/530 

 

OPERATING MANUAL

VERSION 02/2015

ORDER NUMBER DOC2349369

DANGER

Incorrect maintenance/repair!

Danger to life and equipment damage.

  Only a WAGNER service center or a suitably trained person may 

carry out repairs and replace parts.

  Only repair and replace parts that are listed in the Chapter 

"Spare parts" and that are assigned to the unit.

 Before all work on the device and in the event of work 

interruptions:

 

- Switch off  the energy and compressed air supply.

 

- Relieve the pressure from the spray gun and device.

 

- Secure the spray gun against actuation.

  Observe the operating manual and service manuals at all times 

when carrying out work.

13.2 

SPARE PARTS LIST GM 1-350/530

Spare parts list GM 1

35 MPa

Order No.

53 MPa

Order No.

Designation

1

1

2347536

2346856

GM1

2

1

2346614

2346614

Handle

3

1

2353559

2353559

Filter housing with guard bracket

4

1

-

2353599

Trigger guard 4F, complete

4

1

2353600

-

Trigger guard 2F, complete

5

1

347335

347335

Pressure spring

6

1

-

2353606

Preload nut, 530 bar

6

1

2353607

-

Preload nut, 350 bar

7

1

2353556

2353556

Valve rod unit

8

1

2353546

2353546

Intermediate piece "G" 7/8-14-UNF

9

2

9910403

9910403

Cap nut

10

1

2343085

2343085

Bolt

11

1

2353611

2353611

Filter socket with seal

12

1

2353613

2353613

Spray gun body

13

2

43411

43411

Actuating pins

14

1

364340

364340

Seal, fi lter

15

1

-

-

Filter insert, yellow (middle), 100 mesh per inch *

1

2315723

2315723

* Filter insert, red (fi ne), 200 mesh per inch – 10 pieces

1

2315724

2315724

* Filter insert, blue (middle), 150 mesh per inch – 10 pieces

1

2315725

2315725

* Filter insert, yellow (middle), 100 mesh per inch – 10 pieces

1

2315726

2315726

* Filter insert, white (coarse), 50 mesh per inch – 10 pieces

Identifi cation in spare parts lists.

Explanation of column "

K

" (labeling) in the following spare parts lists:

Wearing parts

Note

: These parts are not covered by warranty terms.

Not part of standard equipment, available, however, as additional extra.

Содержание PROTEC GM 1-350

































Отзывы: