WAGNER Control Pro 150 Скачать руководство пользователя страница 2

2

Control Pro 150

AUS

Warning!

Never put your fingers, hands or any other parts of the body into the

spray jet!

Never point the spray gun at yourself, other persons or animals.

Never use the spray gun without safety guard.

Do not treat a spraying injury as a harmless cut. In case of injury to

the skin through coating materials or solvents, consult a doctor

immediately for quick and expert treatment. Inform the doctor

about the coating material or solvent used.

The operating instructions state that the following points must

always be observed before starting up:
1. Faulty units must not be used.
2. Secure spray gun using the safety catch on the trigger. 
3. Ensure that the unit is properly earthed. The connection

must take place through a correctly earthed two-pole and earth

socket outlet.

4. Check allowable operating pressure of high-pressure hose and 

spray gun.

5. Check all connections for leaks. 

The instructions regarding regular cleaning and maintenance of the

unit must be strictly observed.
Before any work is done on the unit or for every break in work the

following rules must be observed:
1. Release the pressure from spray gun and hose.
2. Secure the spray gun using the safety catch

on the trigger.

3. Switch off unit.

Be safety-conscious !

Attention: Danger of injury by injection!

Airless units develop extremely high spraying pressures.

Danger

1

2

3

Содержание Control Pro 150





















Отзывы: