background image

English

14

 

© Wagner Spray Tech - All Rights Reserved

Reassembly

To Reassemble:

  1.  Install the nozzle seal* (1) with the groove (a) (slot) facing 

toward the nozzle (away from the front end assembly).

  2.  Insert the nozzle (2).  Make sure to align the groove (b) 

and notch (c) and align the nozzle opening with the 

needle.

  3.  Put the air screen (d) in the air cap (e). Put both (3) on the 

nozzle (2) and secure with the connecting nut (4).

note:  This step is easier if the spray gun is facing up.

  4.  Snap the adjustment ring 

(5) into the connecting nut (4)

enabling the adjustment lever (f) on the peg (g) to be 

positioned in the air cap.   

note:  Make sure that the two recesses on the adjustment 

ring are engaged in the air cap tabs.   

  5.  Reassemble the spray gun.

note:  Make sure the air valve tube is free of paint.  If not, 

clean the air valve tube by following the instructions on 

the next page.   If clean, make sure it is attached securely at 

both ends (see inset).  

(b)

2

(c)

(a)

1

3

4

2

5

4

(g)

(f)

5

2

1

* Nozzle seal - DO NOT LOSE

It is important that the nozzle seal 

inside the nozzle be re-installed 

properly.  Make sure the cup side of the 

seal (the side with the groove) is facing 

out towards the front of the nozzle.  

Improper installation will cause leakage.

Groove

(d)

(e)

3

4

Содержание 0529017





















Отзывы: