Wacker Neuson DV60 Скачать руководство пользователя

Страница: 73 / 212

BA D24 en/us* 1.0 * D24_1_0_400.fm

4-11

Putting into operation 4

Visual aids

WARNING

Risk of injury to persons in the danger zone!

Persons in the danger area are possibly not seen when reversing the
vehicle and this can cause accidents with serious injuries or death.

► Adjust the existing visual aids (for example the rearview mirrors)

correctly.

► Interrupt work immediately if persons enter the danger zone.
► Pay attention to the movements and changing positions of persons.

WARNING

Accident hazard due to restricted field of vision on the job site!

Accidents resulting in serious injury or death can be caused by a restricted
field of vision.

► Do not allow anyone to stay in the danger zone.
► Use suitable visual aids if necessary (for example a camera, mirrors,

bystander).

► Additional equipment must not be installed if it impairs visibility.

WARNING

Accident hazard due to incorrect adjustment of visual aids!

Incorrectly adjusted visual aids can cause serious injury or death.

► Before starting work, ensure that all visual aids are clean, functional

and adjusted in accordance with the instructions in this Operator’s
Manual.

► If no image appears on the camera monitor, stop vehicle operation.

Only put the vehicle back into operation once the damage has been
repaired.

► Immediately replace damaged or broken visual aids.
► Convex mirrors enlarge, reduce or distort the field of view.
► The operator must follow the national and regional regulations.

• Use safety-oriented ladders and work platforms for adjustment work on

the vehicle.

• Do not use machine components as a climbing aid.
• Set the skip to travel position before adjusting the mirrors.

Содержание DV60





















































































































































































































Результаты поиска

Содержание DV60

Отзывы:

Похожие инструкции для DV60

Бренды по названию

Популярные бренды

Wacker Neuson DV60, Руководство оператора

Результаты поиска

Содержание DV60

Отзывы:

Похожие инструкции для DV60

Бренды по названию

Популярные бренды