Wachs WS-164 Скачать руководство пользователя страница 73

Страница: 73 / 96

15/16"

9/16"

3/16

TYP.

PRODUCTION RELEASE

12/22/2009

REV.

DESCRIPTION

DATE

APR.

REVISION HISTORY

ITEM NO.

PART NUMBER

DESCRIPTION

QTY.

10-010-16-224

PLATE, BULKHEAD

Brennan 2706-08-08

MP-MJ BULKHEAD STRAIGHT

Brennan 2706-16-16

MP-MJ BULKHEAD STRAIGHT

Brennan 0306-16

NUT, BULKHEAD

Brennan 0306-08

NUT, BULKHEAD

SIZE

REV.

DWG. NO.

10-010-16-224B

DRAWN BY

APPROVED BY

DATE

SCALE

SHEET

1:3

1 OF 2

TITLE

PROPRIETARY AND CONFIDENTIAL: THE INFORMATION CONTAINED IN THIS DRAWING IS THE

SOLE PROPERTY OF E.H. WACHS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE

WRITTEN PERMISSION OF E.H. WACHS IS PROHIBITED.

UNLESS OTHERWISE SPECIFIED:

TOLERANCES:

FRACTIONS 1/32

ONE PLACE DECIMAL .015

TWO PLACE DECIMAL .010

THREE PLACE DECIMAL .005

ANGULAR 15 MIN.

DO NOT SCALE DRAWING.

E.H. WACHS WORKMANSHIP STANDARDS (WI 17-01)

SHALL APPLY TO ALL ITEMS NOT SPECIFIED ON DRAWING.

E.H. WACHS

600 Knightsbridge Parkway

Lincolnshire, IL 60069

www.ehwachs.com

J. WILLIAMS

WELDMENT, BULKHEAD PLATE

KRP

08/13/09

ALL DIMENSIONS ARE IN INCHES.

Содержание WS-164

































































































Результаты поиска

Содержание WS-164

Отзывы:

Wachs WS-164, Руководство пользователя, Страница: 73 / 96

Результаты поиска

Содержание WS-164

Отзывы: