manualshive.com logo in svg

Wabtec Ricon TITANIUM S Series, Руководство по обслуживанию, Страница: 35 / 76

Поделиться
Скачать
Wabtec Ricon TITANIUM S Series Скачать руководство пользователя страница 35

3 - 6 

MAINTENANCE 

JUNE 2021

 

32DSKF02.D

 

TITANIUM S-SERIES AND K-SERIES 

PUBLIC USE SERVICE MANUAL 

5.

BRIDGEPLATE 

ADJUSTMENT

NOTE:  

The purpose of the bridgeplate adjustment is to adjust the floor level setting by adjusting the Up Cutoff 
Adjustment Screw and Deploy Cutoff Adjustment Screw so that the bridgeplate properly sits onto the 
bridgeplate switch sensor assembly. 

a. Fully 

STOW 

platform.

b. Refer 

to 

Figure 3-5.

1) Insert screwdriver into the DEPLOY CUTOFF ADJUSTMENT SCREW (bottom adjusting screw).
2) Deploy the platform to floor level.  Push and hold control pendant DEPLOY switch.

RSM0051200

1

2

SWITCH ASSY FOR RH PUMP SHOWN

FIGURE 3-5:  BOTTOM ADJUSTING SCREW 

c. Slowly turn DEPLOY CUTOFF ADJUSTMENT SCREW 

clockwise

 until the bridgeplate moves onto the

bridgeplate switch sensor assembly, as shown in 

Figure 3-6

.

RSM0051300

BRIDGEPLATE SWITCH
SENSOR ASSEMBLY

BRIDGEPLATE
(INNER ROLLSTOP)

BASEPLATE

FIGURE 3-6:  BRIDGEPLATE ADJUSTMENT 

d. DEPLOY platform about 10 inches from ground.
e. Refer 

to

 

Figure 3-7

.  Insert the screwdriver into the UP CUTOFF ADJUSTMENT SCREW (top adjusting

screw) then push and hold control pendant UP switch to cycle the platform back up to floor level.

Содержание Ricon TITANIUM S Series













































































Отзывы:

Нет отзывов