WABCO MICO ACV-DMO-RV, Инструкция по эксплуатации, руководство пользователя и сервисные инструкции

Страница: 3 / 8

Form No. 81-463-019 Revised 2017-06-01
(3)
MICO, Inc.
TABLE 1
(Specifications)
Model
Number
Repair Kit
Number
Nominal
High Limit (cut out)
bar (PSI)
Nominal
Low Limit (cut in)
bar (PSI)
06-463-415
06-463-424
06-463-425
06-463-426
06-463-432
06-463-434
06-463-439
06-463-440
06-463-441
06-463-455
06-463-496
06-400-184
06-400-184
06-400-452
06-400-184
06-400-184
06-400-184
06-400-439
06-400-228
06-400-439
06-463-498
06-400-184
103.4 ± 3.5 (1500 ± 50)
186.2 ± 3.5 (2700 ± 50)
175.8 ± 3.5 (2550 ± 50)
181.0 ± 3.5 (2625 ± 50)
155.1 ± 3.5 (2250 ± 50)
127.6 ± 3.5 (1850 ± 50)
168.9 ± 3.5 (2450 ± 50)
193.1 ± 3.5 (1850 ± 50)
127.6 ± 3.5 (1850 ± 50)
172.4 ± 3.5 (2500 ± 50)
188.6 ± 3.5 (2735 ± 50)
86.2 ± 3.5 (1250 ± 50)
155.1 ± 3.5 (2250 ± 50)
146.5 ± 3.5 (2125 ± 50)
150.0 ± 3.5 (2175 ± 50)
125.8 ± 3.5 (1825 ± 50)
103.4 ± 3.5 (1500 ± 50)
150.0 ± 3.5 (2175 ± 50)
137.9 ± 3.5 (2000 ± 50)
103.4 ± 3.5 (1500 ± 50)
125.8 ± 3.5 (1825 ± 50)
140.3 ± 3.5 (2035 ± 50)
NOTE: If your product number is not listed, please contact MICO, Inc. for information.
Items included in Repair Kit
Not used on all models
Model number 06-463-425 will reuse poppets (34 & 38).
NOTE
Model numbers 06-463-415, 06-463-440, and
06-463-455 use a ball in place of poppet (28).
This ball is not included in the repair kit.
FIGURE 1
Figure 1b
Figure 1a
VALVE ADJUSTMENT
(Refer to Table 1)
1. See machine servicing instructions to properly reinstall accumu-
lator charging valve. Tee an accurate pressure gauge on an
accumulator line.
2. Start pump and allow approximately one minute for charging to
start (pressure in gauge will read accumulator precharge plus).
If valve does not begin to charge remove plug (8) and turn screw
(10) in, stopping when gauge shows an increase in pressure.
Check the high limit specifications (see TABLE 1) and adjust
screw (10) until the high limit setting is met. Reinstall plug (8).
This pressure can be checked correctly only if after each adjust-
ment of screw (10) the accumulator pressure is reduced below
the low limit setting and the system recharges the accumulator
pressure to its high limit. Repeat process until high pressure
setting is accurately adjusted. NOTE: Be sure to reinstall plug
(8) before starting pump.
3. Torque plug (8) 47.5-54.2 N·m (35-40 lb·ft).