manualshive.com logo in svg

WABCO 1200 Plus MCP, Руководство по обслуживанию

Поделиться
Скачать
WABCO 1200 Plus MCP Скачать руководство пользователя страница 29

3   

Troubleshooting and Testing

25

Meritor WABCO

 Maintenance Manual 34 (Revised 03-16)

Maintenance Tips

With proper maintenance, the Meritor WABCO air dryer will provide 
years of reliable service, even under adverse operating conditions. 
To provide additional protection against the harmful effects of 
extreme heat or cold, here are a few helpful tips.

Dedicated Purge Tank

Optimum mounting location for the dedicated purge tank is above 
the air dryer.

Extreme Heat

Make sure the compressor discharge line is long enough to keep 
inlet air below 175

°

F (80

°

C). Figure 3.1. (Refer to Section 5.)

Figure 3.1

Extreme Cold

Make sure the air dryer heater is in good working order by running a 
heater resistance test. Refer to the procedure in this section.

Check the line from the governor to port 4 of the dryer for oil and/or 
water. Keep this line clean to help prevent freezing.

Meritor WABCO air dryer components are installed in the air dryer at 
the factory and are designed to last for the life of the dryer. Under 
some operating conditions, however, a replacement may be 
required. Refer to Section 2 for replacement guide instructions.

Figure 3.1

100215

9a

Содержание 1200 Plus MCP





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды