Vulcan-Hart GR Series Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 56

background image

SERVICE

SETTINGS

KEY SEQUENCE

DISPLAY

ITEM

DESCRIPTION

6.) Display

Press 6 to adjust the left and right display screen
settings. Refer to LCD display screen picture under
ENTER SERVICE SETTINGS MODE.

Press the left or right arrow key on control panel to
select the screen to adjust.

To adjust the selected screen:

•

BACKLIGHT - Press toggle key to turn display
backlight ON or OFF.

•

PIXEL MODE - Press product key number 1 two
times to change display from white background
with black letters to black background with white
letters. Press the key again to change it back to
original setting.

•

CONTRAST - Press the L key on the keypad to
lower the contrast or press the R key on the
keypad to raise the contrast.

N/A

THIS LCD SELECTED

Exit Diagnostic
and Service
Mode

Press PROGRAM Key to exit the selected
DIAGNOSTICS test and return to Service Settings
Mode.

N/A

SERVICE SETTINGS

(shown on display screen)

NOTES:

1

Default values shown in bold.

Alarm Messages

The alarms take precedence over any other controller
mode or function (outputs off, active timers canceled).

ALARMS

DESCRIPTION

PROBE FAULT

If a temperature probe fault occurs, the alarm sounds continuously and the
display shows PROBE on the left display and either OPEN or SHORT on the
right display. This alarm state will remain until the fault clears or power switch
is cycled.

•

OPEN - Probe detects temperature less than 40°F.

•

SHORTED - Probe detects temperature greater than 460°F.

IGNITION STATUS

GAS -Selected under service
settings - Type.

If the ignition status input is not present, both displays show IGNITION
LOCKOUT. If the input comes back in less than 8 seconds, the displays will
revert to normal operation.

If the input remains inactive for more than 90 seconds, IGNITION LOCKOUT
will be shown on the left display and CHECK GAS SUPPLY will be shown right
display, and the alarm will sound continuously. This alarm state will remain until
power switch is cycled.

IGNITION STATUS

GAS Selected incorrectly under
service settings - Type.

After 20 seconds in normal operation mode, IGNITION LOCKOUT will be shown
on the left display and CHECK GAS SUPPLY will be shown right display, and
the alarm will sound continuously.

Enter SERVICE SETTINGS and select GAS* as the type.

GR Series Gas Fryers with NCC Controls (formerly Tridelta / Built after 3/05) - SERVICE PROCEDURES AND

ADJUSTMENTS

Page 35 of

56

F35660

Rev. A (0717)

«
...
33
34
35
36
37
...
»

Содержание GR Series

























































Отзывы:

Нет отзывов

Похожие инструкции для GR Series

Бренд: Haier Страницы: 10

Бренд: Haier Страницы: 7

Бренд: Maytag Страницы: 5

FAMILY PRO ACCESS

Бренд: TEFAL Страницы: 15

Бренд: Stirling Страницы: 24

Бренд: Handy Dryers Страницы: 6

Бренд: Candy Страницы: 26

Бренд: Candy Страницы: 32

Бренд: Parmco Страницы: 15

AF822 Twin Tank

Бренд: AUSTHEAT Страницы: 28

Бренд: Biodrier Страницы: 7

Бренд: Fisher & Paykel Страницы: 78

Бренд: Ginnys Страницы: 16

Бренд: Exido Страницы: 1

Бренд: Roland Страницы: 40

Бренд: RCA Страницы: 42

Бренд: Kelvinator Страницы: 16

Бренд: Cook's Companion Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды