Specifications are subject to change without notice.
© 2018 VTech Communications, Inc. All rights reserved.
01/18. VM3261-2_QSG_V1.
Document order number: 96-012000-010-100
Basic operation -
Parent unit
Adjust speaker volume
Press
VOL -
or
VOL +
to adjust your parent unit
speaker volume. It determines the volume of sound
transmitted from your baby units.
Zoom
Press to zoom in or out.
Talk to your baby unit
Press and hold
TALK
and speak to your parent unit.
Your voice is transmitted to the baby unit.
Turn off the screen
Press and hold
LCD ON/OFF
to switch off the screen.
You can still hear sound from the selected baby unit.
Turn off the parent unit
Press and hold
to power off your parent unit.
Basic operation -
Baby unit
Night vision
The baby unit has infrared LEDs that allow you to
see your baby at night or in a dark room. When
the baby unit detects low light levels, the infrared
LEDs turn on automatically. The images from the
baby unit are in black and white, and
appears
on screen.
NOTES
• It is normal if you see a short white glare on your
parent unit screen as the baby unit is adapting to the
dark environment.
• When the infrared LEDs are on, the images are in
black and white. This is normal.
TIP
• Depending on the surroundings and other
interfering factors, like lightings, objects, colors and
backgrounds, the display resolution may vary. Adjust
the baby unit’s angle, or place the baby unit at a
higher level to prevent glare and blurry display.
Turn off the baby unit
Slide the
ON/OFF
switch to
OFF
to power off
your baby unit.
Press
to switch to another camera in
SINGLE-CAM
mode.
Change different views -
Single-cam
Change different views -
Patrol
In PATROL mode:
1. Press
MENU
when the parent unit is idle.
2. Press or to choose
, then press .
3. Press or to switch on or off
PATROL
mode, then press
SELECT
to confirm your selection.
Sound activation
When the baby unit being viewed detects no sound, the
parent unit screen stays off to save power. Once a sound is
detected, the parent unit screen turns on automatically. It will
then turn off again after 50 seconds of no sound detection.
Press
.
10s
Use the menu
Press
MENU
to enter the main menu, or save a setting.
You can use the parent unit for advanced settings or
operations, such as to play or stop the baby unit lullaby,
or to adjust the baby unit sound sensitivity.
While in the main menu:
• Press or to scroll among the menu options.
• Press to enter the desired submenu.
• Press
MENU
to exit the main menu.
While in the submenu:
• Press or to scroll among the submenu options.
• Press to enter the desired 2nd level submenu.
• Press
SELECT
to confirm your selection.
• Press to exit the submenu.
If you drill the holes into a stud,
go to step 3.
-OR-
If you drill the holes into an
object other than a stud, insert
the wall anchors into the holes.
Tap gently on the ends with a
hammer until the wall anchors
are flush with the wall.
Mount the baby unit (optional)
You can maximize your baby unit’s viewing angles by
tilting the wall mount bracket.
Hold the baby unit, and then rotate the knob in
anticlockwise direction. This will loosen the joint of the wall
mount bracket.
Tilt your baby unit up or down to adjust to your preferred
angle.
Then, rotate the knob in clockwise direction to tighten the
joint and secure the angle.
6U]KXOTMULL
6U]KXOTMULL
TIP
• Press any keys on the parent unit to turn on the screen again.
Long press
2s
Place the wall mount bracket on a
wall and then use a pencil to mark
the top and the bottom holes as
shown. Remove the wall mount
bracket and drill two holes in the wall
(7/32 inch drill bit).
NOTES
• Check for reception strength and
camera angle before drilling the holes.
Align the wall mount bracket and
screws with the holes in the wall
as shown. Tighten the screw in the
middle hole first, so that the wall
mount bracket position is fixed.
You can tighten the other screw in
the top hole.
Place the baby unit on the wall
mount bracket. Tighten the screw into
the threaded socket at the bottom to
secure the baby unit.
OR
Insert the screws into the holes
and tighten the screws until
only 1/4 inch of the screws are
exposed.
Place the baby unit on the wall mount bracket. Tighten
the screw into the threaded socket at the bottom to
secure the baby unit. Align the holes on the wall mount
bracket with the screws on the wall, and slide the wall
mount bracket down until it locks into place.
Submenu
Mainmenu
Press and hold
63
℉
> More than 1
meter (3 feet)
63
℉