manualshive.com logo in svg

VQ CESSNA 208, Инструкция по эксплуатации

Поделиться
Скачать
VQ CESSNA 208 Скачать руководство пользователя страница 2

1.5mm

B

!

CA

L/R

Assemble left and right 
sides the same way.

X

Drill holes using the stated

size of drill 
(in this case 1.5 mm ÿ)

Use epoxy glue

Take particular care here

Hatched-in areas:

remove covering
 film carefully

Not included.
These parts must be

purchased separately

Check during assembly that these

parts move freely, without binding

Apply cyano glue

EPOXY A

EPOXY B

CA

GLUE

Epoxy Glue (  5 minute type)

Thread locker

Cyanoacrylate Glue

Minimum 6 channel radio
for airplane with 2 standard servos
and four servo mini. (five in case of GP)

.60 ~.70 - 4 cycle

11x6 for .46    - 2 cycle engine
12x6 for .60    - 4 cycle engine
12x7 for .70    - 4 cycle engine
13x7 for electric motor

Silicone tube

Extension for aileron
servo, retract servo
and Rx battery pack.

.46 ~ .50 - 2 cycle

Epoxy Glue (30 minute type)

TOLLS REQUIRED

Hobby knife

Needle nose Pliers

Phillip screw driver

Awl

Scissors

Wire Cutters

(Purchase separately)

Hex Wrench

.........................................................

.........................................................

.........................................................

.........................................................

.........................................................

.........................................................

.........................................................

.........................................................

.........................................................

.........................................................

.........................................................

Sander

Masking tape - Straight Edged Ruler - Pen or pencil  - Drill and Assorted Drill Bits

Read through the manual before you begin, so you will have an overall idea of what to do.

Symbols used throughout this instruction manual, comprise:

(Purchase separately)

.Motor control x1(for GP)  .Elevator x1 . Rudder x1 (standard servo)
.Aileron and Flapx2 (mini servo)

CONVERSION TABLE

1.0mm = 3/64”
1.5mm = 1/16”
2.0mm = 5/64”
2.5mm = 3/32”

3.0mm = 1/8”
4.0mm = 5/32”
5.0mm = 13/64”
6.0mm = 15/64”

10mm = 13/32”
12mm = 15/32”
15mm = 19/32”
20mm = 51/64”

25mm = 1”
30mm = 1-3/16”
45mm = 1-51/64”

If exposed to direct sunlight and/or heat, wrinkels can appear. Storing the
model in a cool place will let the wrinkles disappear. Otherwise, remove
wrinkles in covering film with a hair dryer, starting with
low temperature. You can fix the corners by using a hot iron.

Bei Sonneneinstrahlung und/oder Wärme kann die Folie erschlaffen bzw. Falten
entstehen. Verwenden Sie ein Warumluftgebläse (Haartrockner) um evtl. Falten aus der Folie
zu bekommen. Die Kanten können Sie mit einem Bügeleisen behandeln. Nicht zuviel Hitze anwenden !

REQUIRED FOR OPERATION (Purchase separately)

More info: www.pichler-modellbau.de

Low seting

A

700Watt

Содержание CESSNA 208





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды