manualshive.com logo in svg

VQ Models VQA090, Инструкция по эксплуатации

Поделиться
Скачать
VQ Models VQA090 Скачать руководство пользователя страница 10

65 ~ 70mm

20mm

10mm

10mm

10mm

Aileron /

Rudder

Elevator /

10mm

20mm

Querruderausschlag

Hohenruderausschlag

Seitenruderausschlag

Do not try to fly an out-of balance model!

Uberprufen Sie vor dem Flug den Schwerpunkt.

IMPORTANT:

Please do not clean your model with pure alcohol, only use liquid soap with water or use glass cleaner
to clean on surface of your model to keep the colour not fade.

All details are subject to change
without notice !

Technische Anderungen und Irrtumer
vorbehalten !

25mm Landing / Landung

Fflap /

Landeklappen

10

Note: Cut out the stickers and apply them in the
proper area. Do not peel the backing paper off all
at once.
Peel off one corner of the backing and cut off with
scissors.
Arrange sticker on model and when satisfied adhere
the corner without backing.
Carefully peel back the rest of the backing while at
the same time adhering the rest of the sticker.

Try not to make air bubbles, if there are some,
carefully puncture sticker (center of bubble) but not
model surface with the tip
of the knife or sharp pin and squeeze out the air.
At curves stretch sticker and apply a little heat so
that no ceases occur.
Cut off the excess that is produced.

11

12

15mm Take off / Start

CG

Содержание VQA090












Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды