manualshive.com logo in svg

VQ Models F6F HELLCAT, Инструкция по эксплуатации

Поделиться
Скачать
VQ Models F6F HELLCAT Скачать руководство пользователя страница 18

VERTICAL STABILIZER

CA

Plastic control horn

2x12mm screw

............................2

.......................4

Plastic back plate

...........................2

Push the rudder push-rod with clevis into the black nylon push-rod
guide.

Using the plastic control horn as a template, mark
the mounting hole positions, where the rudder clevis
meet the rudder control horn with a felt tipped or a pencil.

Remove the control horn and drill two 2mm
holes through the rudder . 

Attach the rudder control horn using the hardware provided
(two 2x15mm screws and a back plate).

Control horn Alignment

STABILIZER

Push the elevator push-rod with clevis into the black nylon 
push-rod guide.

Using the plastic control horn as a template, mark
the mounting hole positions, where the elevator clevis
meet the rudder control horn with a felt tipped or a pencil.
Move the plastic control horn and drill two 2mm holes 
through the elevator. 

Plastic control horn

2x12mm screw

............................1

.......................2

Plastic back plate

...........................1

2mm

2mm

Attach the elevator control horn using the hardware provided
(two 2x12mm screws and a back plate).

16-  ELEVATOR CONTROL HORN

17-  RUDDER

RUDDER

17A

17B

Содержание F6F HELLCAT

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды