VPI Industries JMW-9 Скачать руководство пользователя страница 7

Playing Records 

 

Before playing a record, make sure that all of the tonearm screws 

are tight.  

 

General Use 

 

Allow at least 20 hours of break-in time.  

 

If you notice hum in the system, remove your interconnects and 

replace them with very cheap, standard VCR interconnects. These 

are well shielded and should eliminate the hum. If the hum goes 

away, get quality, well shielded interconnects. 

 
 

VPI Industries, Inc. Limited Warranty 

VPI Industries, Inc. (VPI) warrants this unit against defects in materials 

and/or workmanship for five (5) years from the date of purchase by the 

original retail purchaser. VPI’s sole obligation under this warranty is limited 

to the repair or replacement, at VPI’s option, of any part(s) found to be 

defective. VPI’s obligation to repair or replace defective parts is the 

purchaser’s sole and exclusive remedy, and VPI shall not be liable for any 

direct or indirect injury and/or property damage arising out of the use of the 

product or defect in or failure of the product.  

This warranty does not extend to any unit whose serial number has been 

defaced or altered. Any product that VPI determines causes a defect or 

malfunction due to incorrect installation, modification, misuse, or servicing 

by the purchaser, or service technician not authorized by VPI to perform 

such service will not be warranted. This warranty does not cover trivial or 

cosmetic defects that do not impair the unit’s normal function. 

VPI reserves the right to make changes in this product without assuming any 

obligation to install such change in any product previously manufactured. 

This warranty to repair or replace defective parts is in lieu of all other 

express or implied warranties of merchantability or fitness for a particular 

purpose. There are not warranties that extend beyond the description 

herein. 

Some states do not allow exclusion of implied warranties or limitation of 

incidental or consequential damages, so the above exclusion or limitations 

may not apply to you. This warranty gives you specific legal rights, and you 

may also have other rights that vary from state to state.  

 
 

Содержание JMW-9








Отзывы: