VPI Industries Classic Direct Скачать руководство пользователя страница 10

Страница: 10 / 11

rotating the platter continuously while in Stop, will eventually cause a fault condition. Fault

conditions are indicated by blinking all the switches. To recover from a fault, press and hold

the Stop and 33 RPM buttons for 10 seconds.

c. If you wipe your records clean prior to playing them, as many of us do, do so with the

platter stopped. If the platter is turning while using a record cleaner and you force the

platter to stop rotating, you will eventually cause a fault condition. Fault conditions are

indicated by blinking all the switches. To recover from a fault, press and hold the Stop and

33 RPM buttons for 10 seconds.

d. If your Classic Direct Drive turntable is not in use for a long period of time, please

disconnect the power supply from the mains supply.

e. Please take care not to damage the power cord or power supply. Any damage should be

repaired by authorized personnel only. A damaged power cord must be replaced

immediately!

f. Once every year, or if you notice speed variations, you should lubricate the spindle

bearing of the turntable platter with the recommended oil. To do so, place 2 drops of the oil

onto the holes at the top center of the platter.

g. Don’t use harsh cleaning fluids on the Classic Direct Drive turntable. For most cleaning

and dust removal a soft cotton cloth is all that is needed. A spray of window cleaner on a

soft cotton cloth will clean everything else. Under no circumstances use alcohol based or

other solvent cleaners, as these could cause damage to painted surfaces!

h. Should you need to transport or ship your turntable, it advisable to use the original

packing materials. Please, always remove the turntable assembly from the plinth before

shipping, otherwise serious damage can occur!

i. Fault conditions are indicated by blinking all the switches. To recover from a fault, press

and hold the Stop and 33 RPM buttons for 10 seconds. If this does not clear the fault, turn

the power switch Off, wait 30 seconds and turn power the power switch On. If this does not

clear the fault, contact your local VPI distributor for service.

Содержание Classic Direct











