background image

128-9317

3 of 16 

Page 3

 YOUR " CODE HOPPING" TRANSMITTERS

The transmitters included with your new security system use the most advanced and 

secure form of radio frequency transmission available on any current automotive 

security system.

Some of today’s sophisticated auto thieves use a device known as a code grabber, 

which will receive and store the signal from your keychain transmitter, and retransmit 

at a later time to disarm your system.

Your anti code hopping transmitters will change their signal every time the button 

is pressed, so when a thief grabs then retransmits your signal, the alarm system 

will not

 respond.

If your transmitter button is pressed more than fifty times while it is out of range of 

the vehicle ( children playing with your keys ), the transmitter will not operate when 

you return to the vehicle and will need to be realigned to the receiver.

To do this, simply press the lock button two times within a one second time period. 

The system will now respond to that transmitter each time a button is pressed.

 

 NOTE:   

Your system has the option of using a siren, the vehicle horn, or both for 

the sounding device. Where the siren is referenced below, the horn or 

both may in fact chirp, or beep.

  ARMING THE SYSTEM - ACTIVE

1. Turn off the engine, exit the vehicle and close all doors, hood lid and trunk lid.

2. Press and release the Lock button on the keychain transmitter.

 Dash mounted LED begins to flash slowly.

 Parking Lights flash one time.

 Siren sounds one chirp.

If the siren/horn

 

sounds 3 chirps, then you have left a door, trunk, or hood 

lid ajar. Simply close the opened entry point to provide full protection. If the 

siren "chirped" three times, sometime after arming, the exclusive delayed 

dome light learn circuit has been programmed and the system detected a 

open entry point after the learned delay expired. Again, closing the hood, 

trunk, or doors will correct the problem and you do not need to disarm 

the system to make the correction. If the siren/horn did not sound when 

arming, then the chirps have been turned off and you should refer to the 

section titled "ELIMINATING THE ARM/DISARM CHIRPS" in this manual.

 Doors Lock - Optional

 Headlight Illumination - Optional

Содержание PRO9644E

















Отзывы: