Dome Light Delay / Theater Dimming
The system can be programed to delay arming after the lock button is pressed
(60 second max) for vehicles with a dome light delay or theater dimming feature.
Once programed the system will ‘learn’ the timing of the dome light delay and add 2
seconds before arming.
1. Close all doors with ignition off.
2. Using the transmitter press LOCK, UNLOCK, LOCK ,UNLOCK, LOCK ,
UNLOCK, LOCK. The LED will light solid to indicate the system has
entered DOME DELAY LEARN MODE.
3. Immediately OPEN then CLOSE the door WITHOUT disarming the
system. The system will then monitor the door trigger wire. Once the
dome light turns off, the system will then add 2 seconds and then exit
the learning mode.
4. The LED will begin to flash indicating the system has exited the
learning mode and is now armed.
Defaulting the Dome Light Delay:
Turn the ignition ON then OFF 3 times then
press and hold the valet button for 5 seconds, the system will chirp 1 time indicating
the learned delay time has been cleared.
User Selectable LED
This feature will control whether the LED is ON or OFF when the system is Armed/
Locked. This will be selectable in feature programming OR on-the-fly without entering
the programming feature banks.
1. Turn the ignition ON, OFF, ON, OFF.
2. Press and release the valet/programming button 3 times. The system
will respond with 1 chirp for ON or 2 chirps for OFF.
PROFESSIONAL
SERIES
Security and Remote Start
Installation Quick Reference
Guide
caSECRS
2 0 1 7 V o x x E l e c t r o n i c s C o r p o r a t i o n . A l l r i g h t s r e s e r v e d .
Adjusting the Shock Sensor
1. Increase sensitivity by turning the adjustment dial clockwise.
2. Decrease sensitivity by turning the adjustment dial counter clockwise.
Tach Programming
The unit will not operate unless tach is programmed or a tachless option is
turned ON
. If an attempt is made to start the vehicle via the remote start without first
programming tach, the unit will flash the parking lights 7 times indicating tach has not
been learned and stored. If the tach rate is not properly programmed to the specific
vehicle, the unit may not realize that the vehicle is running in certain instances and
re-engage the starter motor.
The Remote Start unit will learn the tach rate of most vehicle’s single coil, multiple coil
packs, or single injector. To learn tach:
1. Turn the ignition key to the ON position.
2. Press and release the valet/override button 3 times.
3. Immediately turn the ignition key OFF.
4. Press and hold the valet/override button, then start the vehicle using
the key.
5. When the unit senses the tach signal, the parking lights will begin to
flash.
6. Allow the vehicle to settle to a normal idle speed.
7. Release the valet/program push-button switch. The parking lights will
turn on for 2 seconds and 1 long chip will indicate that the learned
tach signal is stored and the unit has exited tach learn mode.
NOTE:
If the unit fails to learn tach rate due to an improper tach connection or a
poor tach source, the parking lights will not flash. To correct this situation, locate and
connect the PURPLE/WHITE wire to the proper tach signal, and then repeat the tach
learn routine.
Smart Tachless Mode
Smart Tachless Mode is available only if a tach signal has never been learned to the
system and when activated will automatically change the Tach Mode feature in option
programming to Tachless without the need to enter the feature programming mode.
1. Activate the remote start. The parking lights should begin flashing 7
times indicating no tach signal has been learned.
2. Within the 7 flash time period, press and hold the
button.
3. The system will chirp 1 time indicating the system is now in tachless
mode.
Chirp Delete - User Accessible
System ARM/DISARM chirps can be toggled ON or OFF without entering the
programming feature banks.
1. Turn the ignition ON then OFF.
2. Press and release the valet/programming button 3 times. The system
will respond with 1 chirp for ON or 2 chirps for OFF.
RED
BATTERY 12V ( + )
BLACK
GROUND WHEN ARMED ( - )
BLUE
FULL TRIGGER ( - )
GREEN
WARN AWAY TRIGGER ( - )
SHOCK SENSOR & HARNESS
Replacement Part
#4700023
ORANGE
86 - ARMED OUTPUT ( - )
RED
85 - IGNITION ( + )
BLACK
87A - STARTER OUTPUT - MOTOR SIDE
WHITE / BLACK
30 - STARTER INPUT - KEY SIDE
OPEN
87 - OPEN
STARTER INTERUPT RELAY & HARNESS
86
85
30
87
87a
Replacement Part
#1024405
DBI PORT
SHOCK SENSOR PORT
TELEMATICS PORT
BLUE/BLACK
START STATUS / ACTIVE OUTPUT ( - )
PURPLE/WHITE
TACH INPUT
GRAY/RED
PARKING BRAKE INPUT ( - )
GREEN
DOOR TRIGGER INPUT ( - )
BLUE/WHITE
INSTANT TRIGGER INPUT ( - )
WHITE/BLUE
EXTERNAL START INPUT ( - )
PURPLE
DOOR TRIGGER INPUT ( + )
BROWN/RED
BRAKE INPUT ( + )
GRAY
HOOD INPUT ( - )
PINK/BLACK
AUX 5 OUTPUT ( - )
GRAY/BLACK
AUX 3 OUTPUT ( - )
ORANGE
GROUND WHEN ARMED ( - )
VIOLET/BLACK
AUX 1 OUTPUT ( - )
RED/WHITE
TRUNK RELEASE OUTPUT ( - )
BROWN/BLACK
HORN OUTPUT ( - )
LT GREEN/BLACK
FACTORY DISARM / PULSE BEFORE START ( - )
LT BLUE
FACTORY ARM / PULSE AFTER START ( - )
GREEN/WHITE
PULSE AFTER SHUTDOWN ( - )
BLACK/YELLOW
PULSE DURING CRANK ( - )
BLUE/GREEN
FACTORY DISARM 2 / 2ND UNLOCK
ORANGE/BLACK
AUX 4 OUTPUT ( - )
WHITE/BLACK
AUX 2 OUTPUT ( - )
#4120389
WHITE/RED
PARKING LIGHT INPUT
WHITE
PARKING LIGHT OUTPUT
BLACK
GROUND
BROWN
SIREN OUTPUT ( + )
#4120145
BLUE
UNLOCK ( - )
OPEN
GREEN
LOCK ( - )
#1031423
CASECR
S
# 4360698
FLCART PROGRAMMING PORT
FLCART PORT
FLCART HARNESS PORT
PINK
IGNITION 1 ( + )
RED
BATTERY 12V ( + )
PINK/WHITE
IGNITION 2 ( + )
ORANGE
ACCESSORY 1 ( + )
RED/WHITE
BATTERY 12V ( + )
PURPLE
STARTER OUTPUT - MOTOR SIDE ( + )
# 4120110
Replacement Part
Replacement Part
Replacement Part
Remote Start / Power Harness
(6-Pin)
Replacement Part
Replacement Part
Notification Harness
(4-Pin)
Input / Output
Harness
(22-Pin)
Door Lock Harness
(3-Pin)
ANTENNA
LED
VALET
** RF KITS SOLD SEPERATELY **
Replacement Parts
1-Way
# 4180065
2-Way
# 4180065
Harness (4-Pin)
# 4120291
ANTENNA PORT
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
Programming Note:
P
The default wire function settings are listed next
to the wire color. Wires shown with can be
programmed to perform different functions.
Refer to the Feature Programming section to
change the default setting.
P
Security Trigger Zones
If the security system has been triggered the LED will flash one of the patterns below
indicating the zone.
LED FLASHES
TRIGGER ZONE
2 Flashes
Hood / Trunk Input
3 Flashes
Door Input
4 Flashes
Shock Sensor
5 Flashes
Ignition Input
Remote Start Shutdown Diagnostics
If the remote start shuts down or fails to start, the parking lights will flash one of the patterns below indicating the shutdown input.
To manually enter diagnostics and view the last shutdown, turn the ignition ON and press and release the button.
PARKING LIGHT FLASHES
SHUTDOWN ZONE
3 Flashes
Hood / Brake Input
4 Flashes
Remote Start Valet Mode
5 Flashes
Manual Transmission Mode not ready
7 Flashes
Tach not learned / Crank Average not learned
Complete guides also available at
www.voxxuniversity.com
