Vortice VORTICEL MP, Инструкция пользователя

Страница: 11 / 52

11
• Do not use this appliance for functions other than
those described in this booklet.
• After removing the appliance from its packaging,
ensure that it is complete and undamaged. If in
doubt contact a professionally qualified electrician or
Vortice*. Do not leave packaging within the reach of
children or infirm persons.
• If you decide to stop using the appliance, switch it
off and disconnect it from the power supply.
• Do not use this appliance in potentially explosive or
flammable atmospheres or to extract acidic or
corrosive fumes (fig. 1).
• If the appliance is installed at a height of less than
2.5 metres from the floor, it is obligatory to install
protections for moving parts, in the form of the
safety mesh frame and gravity shutter (fig. 4-5).
• If the selected product exceeds 70 dB(A), adequate
noise damping must be fitted when it is installed, or
suitable personal protective equipment used.
Model Lp dB(A) (3m)
MP 302 M - T 75
MP 504 T 74
MP 604 T 79.5
• Do not make modifications of any kind to this
appliance.
• Regularly inspect the appliance for visible defects.
If any faults are found, do not operate the appliance;
contact Vortice* immediately.
• If the appliance does not function correctly or
develops a fault, contact Vortice* immediately.
Ensure that only genuine original Vortice spares are
used for any repairs.
• Should the appliance be dropped or suffer a heavy
blow, have it checked immediately by Vortice*.
• This appliance must only be installed
and serviced, externally or internally,
by professionally qualified personnel.
• Switch off the appliance at the installation's main
switch: a) if the appliance does not function
correctly; b) before cleaning the inside or outside of
the appliance, c) if the appliance is not to be used
for any length of time.
• Ensure that the electrical system to which the
appliance is connected complies with applicable
standards.
• Specifications for the power supply must correspond
to those on the appliance's data plate.
• The circuit in which the appliance is installed
must have an overload protection device
calibrated to suit the nominal current shown on
the appliance's data plate.
• This appliance must be connected to an efficient
earthing system in compliance with applicable safety
standards. If in doubt, ask a qualified electrician to
check your system.
• The electrical power supply/socket to which the
appliance is to be connected must be able to
provide the maximum electrical power required by
the appliance. If it cannot do so, arrange for a
qualified electrician to make the necessary
modifications.
• When installing the appliance, fit a multi-pole
thermomagnetic cutout, with a contact gap of at
least 3 mm.
• If the appliance is installed outdoors, ensure that
adequate weather protection is provided.
• Operating temperature from -25°C to +70°C.
• The temperature of the extracted air must not
exceed 70°C (182°F).
• To ensure correct functioning of this appliance, you
must ensure that there is a sufficient air supply to
the room. If any unsealed fuel burning appliances
(e.g. boilers, gas stoves, etc.) are installed in the
same room, make sure that the air supply is
sufficient for this appliance and to ensure correct
combustion in the other appliance too.
• This appliance must not be used to switch on and
off boilers, heaters etc., nor must it discharge air into
the fume flues of such appliances.
• Do not cover the appliance's intake and outlet.
• Only fit the specified accessories over the intake
and outlet.
• Make sure that the room is adequately ventilated to
ensure proper air circulation.
• Do not allow dust to build up on the motor. This can
Warning:
this symbol indicates precautions that must be taken to avoid injury
!
WARNING - CAUTION
Caution:
this symbol indicates precautions that must be taken to avoid damaging the appliance.
!
*or an authorized Vortice dealer if you are outside the UK-Ireland territory
DESCRIPTION AND OPERATION ENGLISH
The product you have purchased is a medium
pressure, industrial axial fan for air extraction into a
ventilation duct or directly to the outside. It is
designed for installation in ventilation ducts or for extraction through filters in applications where load
loss has be overcome. It must not be used to extract
dusty air or acidic or corrosive fumes (fig. 1).