Vortex 150 MINI Скачать руководство пользователя страница 39

Страница: 39 / 54

Upgrade procedure

1) Remove props, connect a Lipo.

2) Attach the Vortex to a Windows PC or a Mac using a standard Micro-USB cable

(ensure that this is a full

USB cable, and not a power-only cable shipped with some products)

3) Start vortex-configurator from chrome://apps/

4) Make sure the right COM port is selected and press the

Flash Firmware

button.

5) Point to the update file (OSD_vX.X.X.X.fw) downloadable from the

Vortex 150 product page

on the

ImmersionRC website, and start the update.

If during a previous upgrade you had a problem causing the OSD to be bricked, you can still recover from this state

using the procedure below:

Upgrade procedure for bricked OSD

1) Press and hold the button on top of the synergy flight controller (accessible through a hole in the front of

the battery pad).

2) Remove props, plug in the Lipo ( while still holding the fusion board button ).

3) Release synergy board button after 2 seconds.

4) Plug to USB

5) Start vortex-configurator from chrome://apps/

6) Make sure the right COM port is selected and press the

Flash Firmware

button.

7) Point to the update file downloadable from the Vortex product page on the ImmersionRC website, and

start the update.

Flight Controller Firmware Upgrades

To upgrade the Flight-Controller firmware, the same Vortex Configurator tool may be used.

Simply select the BetaFlight .hex file instead of the OSD .fw file when flashing. use the betaflight configurator. :

NOTE: If it failed, wait 1 seconds and retry by clicking Flash Firmware.... Sometimes it may need few

attempts before it starts flashing, so keep trying few times.If after 5 retried it's still not working, retry the

entire procedure.

NOTE: Upgrading Betaflight to a version not supported by the OSD firmware can easily result in the OSD not

functioning. Please refer to the Vortex product page on the ImmersionRC website for compatibility

information.

NOTE: When Vortex will detect a new flight-controller version, it will automatically restart in TX Wizard

mode. If not, force the TX Wizard using the Vortex app.

Содержание 150 MINI























































Результаты поиска

Содержание 150 MINI

Отзывы:

Бренды по названию

Популярные бренды

Vortex 150 MINI, Инструкция по эксплуатации

Результаты поиска

Содержание 150 MINI

Отзывы:

Бренды по названию

Популярные бренды