vonado 42111 страница 22 Скачать руководство пользователя | Manualshive

Страница: 22 / 25

background image

Take the Flicker Effects Board, connect the cable of the light to the Flicker Effects Board
(note: do not connect it to the power port), as per below.

Take a red 15cm dot light, repeat the previous steps to install light for the other pipe,
also connect the cable of the light to the Flicker Effects Board.

«
...
20
21
22
23
24
...
»

Содержание 42111


























Отзывы:

Нет отзывов

Похожие инструкции для 42111

Бренд: RASHA PROFESSIONAL Страницы: 24

Бренд: Ibiza Страницы: 28

Concert EX1S OR3

Бренд: WHITECROFT LIGHTING Страницы: 2

Бренд: RAB Lighting Страницы: 2

Бренд: Somogyi Elektronic Страницы: 12

Бренд: KAM Страницы: 5

Бренд: Heitronic Страницы: 8

Бренд: DOMUS LINE Страницы: 14

MATRIXX FX-440 DMX

Бренд: Stairville Страницы: 16

Бренд: TGS Страницы: 2

Бренд: GE Страницы: 4

Бренд: GE Страницы: 2

Бренд: GE Страницы: 2

Бренд: GE Страницы: 2

Бренд: LIVARNOLUX Страницы: 30

COLORdash Accent Series

Бренд: Chauvet Страницы: 24

ColorAdo 2 Tour

Бренд: Chauvet Страницы: 34

Бренд: Kasco marine Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды