02 Instruments and controls
HomeLink
*
02
``
*
Option/accessory, for more information, see Introduction.
87
The particular distance that is required
between the original remote control and
HomeLink
depends on the programming
of the device in question. Perhaps several
attempts will be required at different dis-
tances. Maintain each position for approx.
15 seconds before trying a new one.
3.
Depress the button for the original remote
control and the button to be programmed
on HomeLink
simultaneously. Do not
release the buttons until the indicator lamp
has changed over from slow to rapid flash-
ing. The rapid flashing indicates successful
programming.
4.
Test the programming by depressing the
programmed button on HomeLink
and
watching the indicator lamp:
•
Constant glow:
The indicator lamp illu-
minates with a constant glow when the
button is kept depressed, this indicates
that the programming is complete. The
garage door, gate or similar should now
be activated when the programmed
HomeLink
button is depressed.
•
Glow not constant:
The indicator lamp
flashes quickly for approx. 2 seconds
and then changes over to a constant
glow for approx. 3 seconds. This proc-
ess is repeated for approx. 20 seconds
and indicates that the device has a "roll-
ing code". The garage door, gate or sim-
ilar is not activated when the pro-
grammed HomeLink
button is
depressed. Continue the programming
in accordance with the following.
5.
Locate the "programming button
1
" on the
receiver for the garage door for example,
normally located close to the antenna's
bracket on the receiver. If you have diffi-
culty in finding the button - consult the
supplier's manual, or contact the supplier
via the Internet: www.homelink.com.
6.
Depress and release the "programming
button". The button flashes for
approx. 30 seconds and the next step must
be carried out within this period.
7.
Depress the programmed button on
HomeLink
, while the "programming but-
ton" is still flashing, keep it depressed for
approx. 3 seconds and then release.
Repeat the press/hold/release sequence
up to 3 times to conclude the program-
ming.
Programming individual buttons
To reprogram an individual button, proceed in
accordance with the following:
1.
Depress the required button on
HomeLink
and do not release until step 3
has been completed.
2.
When the indicator lamp on HomeLink
starts to flash, after approx. 20 seconds,
position the original remote control
5-30 cm from HomeLink
. Monitor the indi-
cator lamp.
The particular distance that is required
between the original remote control and
HomeLink depends on the programming of
the device in question. Perhaps several
attempts will be required at different dis-
tances. Maintain each position for approx.
15 seconds before trying a new one.
3.
Depress the button on the original remote
control. The indicator lamp will start to
flash. When the flashing has changed over
from a slow to a rapid flashing - release
both buttons. The rapid flashing indicates
successful programming.
4.
Test the programming by depressing the
programmed button on HomeLink and
watching the indicator lamp:
1
Button designation and colour vary depending on manufacturer.
Содержание S40 - ANNEXE 244
