manualshive.com logo in svg

Volvo EPA2007 D13F, Справочное руководство


Поделиться
Скачать
background image

BASIC SERVICE 161

Inlet Valve Adjustment

WARNING

Apply the parking brake before barring the engine over. Remove the EMS power
supply fuse to avoid starting the engine unintentionally. Make sure that the
transmission is not in gear.

With the engine cold, 60°C (140°F) or less, check and adjust the valves and injector
as required for each cylinder before moving to the next. Follow this sequence of
cylinders when adjusting clearances: 5, 3, 6, 2, 4 and 1.

1. Using the flywheel turning tool, 88800014, bar the engine over manually to the
appropriate camshaft marking for adjustment of the inlet valves and injector for that
cylinder.

W2033397

2. Using a feeler gauge, check the clearance between the rocker arm adjusting screw
and the valve yoke (bridge) of the inlet valves.

3. If the clearance is not within specification, loosen the locknut and adjust the
clearance as required.

4. Hold the adjusting screw to prevent it from turning and tighten the locknut to
specification.

5. Recheck the clearance after tightening the locknut.

6. Mark the respective rocker arm as each adjustment is completed.

Содержание EPA2007 D13F




















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для EPA2007 D13F

Indmar Raptor JET SERIES Operator'S Manual preview
Raptor JET SERIES
Бренд: Indmar Страницы: 82
KCFA SV-X3 Series Installation And Wiring preview
SV-X3 Series
Бренд: KCFA Страницы: 2
ACM TRONIX 13 Instructions And Warnings For Fitters preview
TRONIX 13
Бренд: ACM Страницы: 37
Deutz TBD 616 OEM Operating Instructions Manual preview
TBD 616 OEM
Бренд: Deutz Страницы: 257
Kohler KD 500 Workshop Manual preview
KD 500
Бренд: Kohler Страницы: 44
GR GR6 Series Manual preview
GR6 Series
Бренд: GR Страницы: 8
Petter AB1W Installation Manual preview
AB1W
Бренд: Petter Страницы: 58
Volvo Penta MD2010 Operator'S Manual preview
MD2010
Бренд: Volvo Penta Страницы: 64
Volvo Penta KAD/KAMD300 Operator'S Manual preview
KAD/KAMD300
Бренд: Volvo Penta Страницы: 104
SSANGYONG Q151 Service Manual preview
Q151
Бренд: SSANGYONG Страницы: 14
Metaphase Technologies Metaphaser MP-LE1007 Operating Manual preview
Metaphaser MP-LE1007
Бренд: Metaphase Technologies Страницы: 35
Teknic ClearPath-SCHP Series User Manual preview
ClearPath-SCHP Series
Бренд: Teknic Страницы: 117
Yanmar 4TNV98T-ZGGE General Specification preview
4TNV98T-ZGGE
Бренд: Yanmar Страницы: 2
Gaspar Xicoy X45 User Manual preview
Xicoy X45
Бренд: Gaspar Страницы: 27
Toyota 3S-GTE Repair Manual preview
3S-GTE
Бренд: Toyota Страницы: 222
Universal atomic four Owner'S Manual preview
atomic four
Бренд: Universal Страницы: 26
HKS 700E Operation Manual preview
700E
Бренд: HKS Страницы: 36
Melec 5411a User Manual preview
5411a
Бренд: Melec Страницы: 42

Бренды по названию

Популярные бренды

Загрузить еще бренды