background image

Engine Oil, Change

 WARNING!

Hot oil and hot surfaces can cause burns.

Oil changes must be done when the engine is warm.

1 Connect the drain hose to the oil drain pump and

check that no leakage can occur.

2 Pump the oil out (or remove the bottom drain plug

and drain the oil).
Collect all the old oil and old filters, and leave them
at a re-cycling station for destruction.

3 Remove the drain hose (or install the bottom drain

plug).

4 Fill with engine oil.

For change volume, please refer to 

Technical

Data page 65

.

Oil Filter/By-pass Filter, Change

 WARNING!

Hot oil and hot surfaces can cause burns.

1 Clean the oil filter bracket (2).

2 Remove all oil filters with a suitable oil filter extrac-

tor (1).

3 Clean the mating surface of the oil filter bracket.

Make sure that no pieces of old oil seal are left
behind. Carefully clean round the inside of the pro-
tective rim (2) on the oil filter bracket.

4 Put a thin layer of engine oil on the seal rings of the

new fuel filters.

5 Install the new oil filters. Tighten the filters ¾–1 turn

after they touch.

6 Top up with engine oil, start the engine and let it run

for 20-30 seconds.

7 Turn off the engine, check the oil level and top up

as required.

8 Check sealing round the oil filters.

 

1

P0015866

 

Maintenance

48

47702660 03-2013  © AB VOLVO PENTA

Содержание TAD734GE

































































Отзывы: