Volvo Penta D7A T Скачать руководство пользователя страница 85

Страница: 85 / 116

Raw Water System

WARNING!

Risk of water entry. Close and drain the raw water
system before starting any work on the system.

Raw Water System, Draining

1 Close the raw water in- and outlet cocks.

2 Open the drains, refer to chapter

General, page 67

, and allow the water to drain.

IMPORTANT!

Check that the raw water really drains. Deposits may
need to be removed from inside the drain plugs/taps.

Impeller, raw water pump

Checking and changing

IMPORTANT!

Always keep a spare impeller and gasket in store
aboard the ship.

1 Close the raw water cocks and drain the external

cooling water as described in the chapter draining
the raw water system.

2 Remove the pump end cover (1), the seal (2), and

the impeller(3).

3 Inspect the impeller. Change the impeller if there

are any visible cracks or other defects.

4 Clean the inside of the housing. Lubricate the pump

housing and the inside of the cover with water-
resistant grease (non-aggressive on rubber).

5 Push the impeller into position while rotating it in the

normal operating direction.

6 Fit the cover with a new seal.

7 Open the raw water cocks.

P0003701

Maintenance

47713337 03-2021 © AB VOLVO PENTA

Содержание D7A T





















































































































Результаты поиска

Содержание D7A T

Отзывы:

Похожие инструкции для D7A T

Бренды по названию

Популярные бренды

Volvo Penta D7A T, Руководство оператора

Результаты поиска

Содержание D7A T

Отзывы:

Похожие инструкции для D7A T

Бренды по названию

Популярные бренды