Volvo Penta D7A T Скачать руководство пользователя страница 107

Страница: 107 / 116

Coolant

WARNING!

All coolant is hazardous and harmful to the
environment. Do not consume. Coolant is flammable.

IMPORTANT:

Always use the same type of coolant that is already in
the engine.
Different types of coolant must not be mixed with each
other.
Risk of reduced cooling function and performance by
clogging and isolation.

Coolant shall be based on Organic Acid
Technology (OAT).

Follow the mixing recommendation on the
product.

The coolant should be mixed with distilled, deionized
water. For Volvo Penta specified water requirements;
refer to

Water Quality, page 105

NOTICE!

Always use “Ready Mixed” coolant if water

quality cannot be determined or if it does not fulfill
ASTM D4985.

NOTICE!

Never mix more than 60% concentrated

coolant with water. A greater concentration provides
reduced cooling effect with the risk for overheating and
reduced freeze protection.

Water Quality

ASTM D4985:

Total solid particles

<340 ppm

Total hardness

<9,5° dH

Chloride

<40 ppm

Sulfate

<100 ppm

pH value

5.5–9

Silica (acc. ASTM D859)

<20 mg SiO

Iron (acc. ASTM D1068)

<0.10 ppm

Manganese (acc. ASTM D858)

<0.05 ppm

Conductivity (acc. ASTM D1125)

<500 µS/cm

Organic content, COD

(acc.

ISO8467)

<15 mg KMnO

Technical Data

47713337 03-2021 © AB VOLVO PENTA

105

Содержание D7A T





















































































































Результаты поиска

Содержание D7A T

Отзывы:

Похожие инструкции для D7A T

Бренды по названию

Популярные бренды

Volvo Penta D7A T, Руководство оператора

Результаты поиска

Содержание D7A T

Отзывы:

Похожие инструкции для D7A T

Бренды по названию

Популярные бренды