VOLTCRAFT DSO-2104 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 66

background image

3.Quick Start

11

probe hook tip is used, ensure that it keeps in close touch with the probe.
Connect the probe tip with the signal connector of the probe compensator
and connect the reference wire clamp with the ground wire connector of
the probe connector, and then push the

Autoset

button on the front panel.

2. Check the displayed waveforms and regulate the probe till a correct

compensation is achieved (see

Overcompensated

Compensated correctly

Under

compensated

Figure 3-6 Displayed Waveforms of the Probe Compensation

3. Repeat the steps mentioned if needed.

Figure 3-7 Adjust Probe

How to Set the Probe Attenuation Coefficient

The probe has several attenuation coefficients, which will influence the vertical
scale factor of the oscilloscope.

To change or check the probe attenuation coefficient in the menu of
oscilloscope:

(1)

Push the function menu button of the used channels (

CH1

-

CH4 button

).

(2)

Select

Probe

in the right menu; turn the

M

knob to select the proper value

in the left menu corresponding to the probe.

This setting will be valid all the time before it is changed again.

«
...
13
14
15
16
17
...
»

Содержание DSO-2104



































































Отзывы:

Нет отзывов

Похожие инструкции для DSO-2104

Бренд: Panasonic Страницы: 180

Бренд: lancer Страницы: 12

Бренд: TC Electronic Страницы: 2

Бренд: Bahco Страницы: 131

Бренд: Bahco Страницы: 126

Coronis 5MP Mammo

Бренд: Barco Страницы: 4

Бренд: Barco Страницы: 167

Color Coronis 2MP

Бренд: Barco Страницы: 156

Color Coronis 2MP

Бренд: Barco Страницы: 12

Бренд: Barco Страницы: 39

Бренд: Barco Страницы: 158

Бренд: Tascam Страницы: 8

Бренд: Keithley Страницы: 79

Бренд: Kayakpro Страницы: 17

Бренд: Yoshitake Страницы: 11

Бренд: Kellfri Страницы: 12

Бренд: Nectar Страницы: 46

Бренд: Neauvia Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды