background image

VOLT

®

 Cast Brass Integrated LED Downlight

VAL-91xx Series

INSTALLATION & MAINTENANCE GUIDE

w w w . v o l t l i g h t i n g . c o m

–2–

Important Safety Instructions: Read Before Installation

This luminaire is intended for installation in accordance with local codes and 

the National Electric Code (NEC). Failure to adhere to these codes and

instructions may result in serious injury, property damage and void the 

warranty.

These instructions do not intend to cover all variations in installation, operation 

maintenance or mounting situation. 

1.  Make sure that the power is turned OFF before installing or servicing this 

luminaire. 

2.  Warning: risk of electrical shock.  Install all luminaires 10 feet (3.05M) or 

more from pool, spa or fountain.

3.  This luminaire is intended to be used only with a power supply 

(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.

4.  Wiring connections must be made with wire connectors that is suitable for 

outdoor use.

5.  Position the low voltage wire and wire connector so that it is located 

within 6 inches (15.2 cm) from a building structure, a luminare, or fitting.

6.  The main low voltage cable is intended for shallow burial - less than 6 

inches (152 mm)

7.  If additional lengths of low voltage cable is required, please contact www.

voltlighting.com or call 1-813-978-3700.

!

SAVE THESE INSTRUCTIONS

Содержание VAL-91 Series







Отзывы: