manualshive.com logo in svg

Vollrath MIN0012, Руководство оператора, Страница: 4 / 12

Поделиться
Скачать
Vollrath MIN0012 Скачать руководство пользователя страница 4

F

ood

 P

reParation

 e

quiPment

O

peratOr

’

s

 M

anual

 4

Grinder Chamber Assembly and installation

1.  If necessary assemble the blade shaft (B) into the worm gear (A). See 

Figure 7.

2.  Slide the shaft washer (A) onto the worm gear shaft (B). See Figure 6.

3.  Slide the shaft washer (A) so that it is seated against the worm gear 

assembly (B) as shown. See Figure 5.

4.  Slide the worm gear assembly (B) and the shaft washer (A) into the 

grinder chamber (C). Slide the worm gear shaft (D) in until it is seated 

fully.

5.  Slide the knife blade (B) so that the flat ground edges (A) face to the 

outside as shown, onto the blade shaft (C). See Figure 8.

C

A

d

B

Figure 8. Knife Blade and Blade shaft Figure

6.  Slide the knife blade (B) onto the blade shaft (C) so that it seats 

completely over the square (D). See Figure 4.

7.  Place the grinder plate (D) onto the blade shaft (A) so that the cutout 

(C) slides over the locating pin (B). See Figure 3.

8.  If a sausage filler is to be used, place it between the coupling cover 

(A) and the grinder chamber (B). See Figure 2.

9.  Thread the coupling cover (A) onto the grinder chamber (B) and 

tighten securely.

6.

A

B

Figure 6. shaft Washer and Worm gear shaft

7.  If desired remove the blade shaft assembly (B) from the worm gear (A). See 

Figure 7

A

B

Figure 7. Blade shaft and Worm gear

Thoroughly clean and dry all parts.

t

roubleshooting

Problem

Possible Cause

Course of Action

Grinder stops operating or output is erratic.  Grinder is overloaded.

Switch to the “Reverse”position momentarily, turn the unit to the “OFF” 

position. Check the following:

 

„

Thumb screw too tight; loosen and hand-tighten, do not over-tighten

 

„

Discharge plate is blocked; remove and clear

 

„

Blade edges are dull; have sharpened or replace

Press the reset button.

Grinder stops operating or output is erratic.  Blades are in backwards.

Correct blade direction.

Metal shavings or particles in food product. Blades are in backwards.

Correct blade direction.

Motor humms but does not operate.

Governor out of adjustment. Adjust governor per procedures posted at Vollrathco.com or contact Vollrath 

Technical Service.

  

s

erviCe

 

and

 r

epair

There are no user serviceable parts within this appliance. To avoid serious injury or damage, never attempt to repair the equipment or replace a damaged power 

cord yourself. Do not send equipment directly to the Vollrath Company. Please contact the qualified professional repair service listed below.

VOllrATh Technical service • 1-800-628-0832

Содержание MIN0012













Отзывы:

Нет отзывов