Volkswagen CJDA Скачать руководство пользователя страница 473 | Manualshive

Страница: 473 / 553

background image

Note

◆

During regeneration the values in the display zones 2 and 3
should decrease.

◆

The two values may decrease down to 0, and the regenera-
tion may still continue.

◆

The regeneration will be completed after 20 min. at the lat-
est, and the engine returns to idling speed.

◆

Allow the engine to run at idling speed for some time so that
the fan can cool down the engine compartment.

– Check soot loading in display zones 2 and 3. Specification:

< 35 g.

– Press

←

button.

– Select “Display group 254”.

If display zone 2 shows the value "1", the regeneration has
been completed successfully.

– Leave the engine switched on.

– Adapt the ash deposit mass

Display zone 2 shows "0"

– If display zone 2 shows "0" or "255", secure machine or read

event memory and rectify faults, read event memory

.

– Repeat regeneration of diesel particulate filter

If the 2nd regeneration has been completed and the display
zone of “display group 254” does not show "1", the oxidising
catalytic converter is presumably defective.

– Then, read event memory of engine control unit, and clear

event memory if necessary, read event memory.

Note

◆

If the specifications have been attained, the regeneration of
the diesel particulate filter has been completed successfully.

◆

The DPF warning lamp goes off after the regeneration of the
diesel particulate filter has been completed successfully.

3.9.3 Cancelling regeneration of diesel particu-

late filter, engine codes CPYA, CPYB,

CPYC, CPYD, CPYE

– The regeneration of the diesel particulate filter is in progress,

and the vehicle diagnostic tester is connected.

– Select diagnosis function “015-Access permissions”.

– If available, select “015.2 Security Access (automatic)”.

– Enter following access code:

● Access code: 23456

– Confirm access code.

Industriemotoren - Industrial Engines 2009

▶

Workshop Manual for Diesel Engine (2.0 l/36-75 kW_EA 189) 05.2015

3

3 Checking components and functions

457

«
...
471
472
473
474
475
...
»

Содержание CJDA










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CJDA

Бренд: Barco Страницы: 54

Бренд: Perkins Страницы: 92

Бренд: pumpa Страницы: 32

Бренд: MINN KOTA Страницы: 42

Бренд: Vanguard Страницы: 124

Бренд: Detroit Diesel Страницы: 135

Бренд: Hino Motors Страницы: 216

Бренд: Hino Страницы: 278

Бренд: O.S. engine Страницы: 38

Бренд: Honda Страницы: 32

Бренд: Honda Страницы: 100

Бренд: Volvo Penta Страницы: 176

Бренд: STEYR Страницы: 331

Бренд: yellow Gardenline Страницы: 64

Бренд: B&R Страницы: 300

Бренд: V2 Страницы: 16

Бренд: Xtreme Power Страницы: 42

Бренд: Stiga Страницы: 232

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды