background image

2.8L VR6

Article Text

This file passed thru Volkswagen Technical Site - http://volkswagen.msk.ru    

ARTICLE BEGINNING

         1999-2000 ENGINES
         Volkswagen 2.8L VR6 6-Cylinder

         Golf, GTI, Jetta

         * PLEASE READ THIS FIRST *

NOTE:    For engine repair procedures not covered in this article,
         see ENGINE OVERHAUL PROCEDURES - GENERAL INFORMATION article
         in the GENERAL INFORMATION section.

         ENGINE IDENTIFICATION

         Engine identification number is stamped on a machined pad, on
front of the cylinder block. See Fig. 1. The engine code is also
listed on a sticker attached to the pulley side of the valve cover and
the vehicle identification sticker located in the luggage compartment.

ENGINE CODES

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

Application                                                      Code

2.8L VR6  ......................................................  AAA
2.8L VR6  ......................................................  AFP

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

Fig. 1:  Locating Engine Identification Number
Courtesy of Volkswagen United States, Inc.

         ADJUSTMENTS

         VALVE CLEARANCE

         Engine is equipped with hydraulic lifters. Adjustment is not
necessary.

         TROUBLE SHOOTING

NOTE:    See TROUBLE SHOOTING - BASIC PROCEDURES article in the
         GENERAL TROUBLE SHOOTING section.

Содержание 1998 Jetta




















Отзывы: