background image

 

 

 

service agent or similarly qualified persons in order to avoid a hazard

.

 

 

INSTALL THE HOOD 

Note 1 : On stainless steel hoods, carefully remove the plastic protective film 
from all exterior surfaces of the hood and chimney prior to final installation.   
Note 2:    At least two people will be required to mount the hood. 

 

INSTALL THE HOOD 

Minimum  hood  distance  above  the  cooker 
must not be less than 650mm. 
A  maximum  of  750mm  above  the  cooker  is 
highly  recommended  for  best  capture  of 
cooking impurities. 
Distance over 750mm above the cooker are at 
the installer’s and user’s discretion - providing 
that ceiling height and flue length permit. 
1.

 

Secure the hood mounting bracket to the 
wall  using  (2)  ST  5  x  50mm  mounting 
screws  and  dry  wall  anchors.  Align  the  hood  body  with  the  hood 
mounting bracket. Gently lower the hood until it securely engages the 
bracket. 

2.

 

Fix the discharge collar into the air outlet adapter. 

3.

 

Attach  an  adequate  length  of  150mm  round  duct  to  the  air  outlet 
adapter. 

4.

 

Carefully slide the decorative chimney top down inside the decorative 
chimney bottom. Carefully place the decorative chimney bottom into the 
recessed area of the hood body top. 

5.

 

Secure  the  chimney  mounting  bracket  to  the  wall  using    (2)  ST  5  x 
50mm mounting screws and dry wall anchors. 

6.

 

Raise the decorative chimney top until its holes align with holes in the 
chimney mounting bracket (located on the wall). 

7.

 

Level the hood and secure the chimney with 2 chimney bracket screws. 

8.

 

Fix the Decorative Chimney Bottom with 3 decorative Chimney Bottom 
screws from inside of body. 

Содержание RH.CAN.600.BL










Отзывы: