background image

TROUBLE SHOOTING 

Fault 

Cause 

Solution 

Light on, but 
motor does not 
work 

The blades are blocked. 
The capacitor is damaged. 

Replace capacitor. 

The motor is damaged. 

Replace motor. 

The internal wiring of motor is cut off/ 
disconnected. An unpleasant smell 
may be produced. 

Replace motor. 

Both light and 
motor do not 
work 

Apart from the above mentioned, check the following: 
Light damaged. 

Replace lights. 

Power cord loose. 

Connect the wires as per the electric 
diagram. 

Oil leakage 

Outlet and the air ventilation entrance 
are not tightly sealed. 

Take down the outlet and seal with glue. 

Leakage from the connection of 
U-shaped section and cover. 

Take U-shaped section down and seal 
with soap or paint. 

Vibration 

The blade, if damaged, can cause 
vibrating. 

Replace the blade. 

The motor is not tightly fastened. 

Fasten the motor tightly. 

The cooker hood is not tightly fixed.  Fixed the cooker hood tightly. 

Insufficient 

suction 

The distance between the cooker 
hood and the cooker top is too large. 

Readjust the distance. 

Too much ventilation from open doors 
or windows. 

Choose a new place to install the 
appliance or close some doors / windows. 

The 
machine 
inclines 

The fixing screws are not tight 
enough. 

Tighten the fixing screw and make it 
horizontal. 

The hanging screws are not tight 
enough 

Tighten the hanging screw and make it 
horizontal. 

11

Содержание 330171













Отзывы: