background image

Page 2

 

VG810CL SENTRY COAL™

 

VGZ-011 / 20120105.0

SAFETY INSTRUCTIONS

Read All Instructions carefully.

1.  The installation of this stove must comply with your 

local building code rulings. Please observe the clear-
ances to combustibles (see reference figures 3–5). Do 
not place fuel, furniture or any other objects within the 
clearance area.

2.  Verify that the stove is properly installed be-

fore firing the stove for the first time. After read-
ing these instructions, if you have any doubt 
about your ability to complete your installation  
properly, you must obtain the services of a  
professional licensed installer familiar with all  
aspects of safe and correct installation.  DO NOT  
use temporar y or makeshift compromises  
during installation. There must be 

NO DEVIATION OR 

ALTERATION OF ANY KIND from the very specific 
instructions spelled out in this instruction manual as 
it pertains to the installation of this woodstove.  NO 
EXCEPTIONS!

3.  DO NOT store coal, kindling, flammable liquids or 

other combustible materials in the vicinity of the ap-
pliance. Refer to certification label on back of unit and 
reference figures 3–5 in this manual.

4. 

DO NOT INSTALL THIS STOVE IN A MOBILE HOME, 
MANUFACTURED  HOME, TRAILER  OR TENT  
NO EXCEPTIONS! (HUD Federal Standard: 24 
CFR Ch.XX).

5. 

DO NOT ELEVATE THIS STOVE BY ANY MEANS. 
(i.e. bricks under legs, cement blocks)  Stove legs must 
set directly upon the solid-surface non-combustible 
floor as specified in this stove instruction manual. 

6. 

DO NOT MODIFY THIS STOVE IN ANY WAY!  
Stove must be installed with legs and bottom heat 
shield provided, attached as shown in the instruc-
tions. 

DO NOT OPERATE WITHOUT BOTTOM HEAT 

SHIELD – NO EXCEPTIONS. Heat Shield must be  
assembled and installed as shown in Assembly In-
structions. Assemble only with original parts as sup-
plied and shown in this manual. 

7. 

DO NOT OPERATE A STOVE THAT IS MISSING 
ANY PARTS!
 If any parts are missing or defective, 
please notify the dealer or manufacturer immediately. 
Replace missing, broken or worn parts with factory 
original or equivalent parts only.

8.  Do not tamper with combustion air control  

beyond normal adjustment capacities.

9.  Always connect this stove to a chimney and vent to the 

outside. Never vent to another room or inside a build-
ing. 

DO NOT CONNECT THIS UNIT TO A CHIMNEY 

FLUE SERVING ANOTHER APPLIANCE.

10. 

DO NOT CONNECT A COAL BURNING STOVE 
TO AN ALUMINUM TYPE B GAS VENT. 
This is 

not safe. Use approved masonry or an Underwriters 
Laboratories Listed UL 103 HT (USA) / ULC-S629 
(CDN) Listed Residential Type and Building Heating 
Appliance Chimney. Use a 6˝/152mm diameter chim-
ney, that is high enough to give a good draft. (See  
specifics in Chimney Connections instructions).

11.  Be sure that your chimney is safely constructed and 

in good repair. Have the chimney inspected by the fire 
department or a qualified inspector. Your insurance 
company should be able to recommend a qualified 
inspector. Chimney connector pipe must be in good 
condition. Replace if necessary before using stove.

12.  Creosote, soot or fly ash may build up in the chimney  

connector and chimney and cause a house/building 
fire. Inspect the chimney connector and chimney 
twice monthly during the heating season and clean if 
necessary. (see Service Hints section in this manual). 

13.  In the event of a chimney fire, turn the air con-

trol and flue damper to closed position, leave the 
building and 

CALL THE FIRE DEPARTMENT  

IMMEDIATELY!  Have a clearly understood plan 
on how to handle a chimney fire by contact-
ing your local fire authority for information on 
proper procedures in the event of a chimney fire.  
After the fire is out, the chimney must be cleaned 
and inspected for any stress or cracks before starting 
another fire.  Check the condition of any combustibles 
surrounding the chimney.

14. 

DISPOSAL OF ASHES Ashes should be placed in 
a steel container with a tight fitting lid and moved 
outdoors immediately. The closed container of ashes 
should be placed on a noncombustible floor or on 
the ground, well away from all combustible materials, 
pending final disposal. If the ashes are disposed of 
by burial in soil or otherwise locally dispersed, they 
should be retained in the closed container until all 
cinders have completely cooled. Other waste shall 
not be placed in this container.

15.  To prevent injury, do not allow anyone to use this 

stove who is unfamiliar with the correct operation of 
the stove.

16.  Do not operate stove while under the influence of 

drugs or alcohol.

17.  The special paints used on your stove may  

give off some smoke and an odor while  
they are curing during the first 12 to 15 fires.  Addi-
tional smoke and odor may be emitted from the light 
oils used in construction of the fire box. This should 
disappear after a short period of time and not occur 
again. Persons with lung conditions or owners of 
susceptible domestic pets (such as birds) should take  
prudent precautions. Open windows and doors as 

Содержание Sentry Coal VG810CL























Отзывы: