background image

MPE Requirements

Le présent appareil est conforme aux CNR d'Industrie Canada applicables auxappareils radio exempts de licence. 

L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et 

(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible 

d'en compromettre le fonctionnement.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's 

authority to operate the equipment.

To satisfy FCC / IC RF exposure requirements, a separation distance of 20 cm or more should be maintained 

between the antenna of this device and persons during device operation.

To ensure compliance, operations at closer than this distance is not recommended.
Les antennes installées doivent être situées de facon à ce que la population ne puisse y être exposée à une distance

de moin de 20 cm. Installer les antennes de facon à ce que le personnel ne puisse approcher à 20 cm ou moins de 

la position centrale de l’ antenne.

La FCC des éltats-unis stipule que cet appareil doit être en tout temps éloigné d’au moins 20 cm des personnes 

pendant son functionnement

Caution:

FCC Declaration

This device complies with Part 15 of the FCC Rules / Industry Canada licence-exempt RSS standard(s). Operation

is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must 

accept any interference received, including interference that may cause undesired operation.

Apple, iPad, iPad Air, iPhone, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries.

HomeKit is a trademark of Apple Inc. 
Use of the Works with Apple HomeKit logo means that an electronic accessory has been designed to connect 

specifically to iPod, iPhone, or iPad, respectively, and has been certified by the developer to meet Apple performance 

standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
Controlling this HomeKit-enabled accessory automatically and away from home requires an Apple TV with tvOS 10.1

or later or an iPad with iOS 10.1 or later set up as a home hub. 
To control this HomeKit-enabled accessory, iOS 10.1 or later is recommended.

Legal Information

10

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a 

residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed 

and used in accordance with the instructions, may cause harmful interference to radio communications. However, there 

is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful 

interference to radio or television reception, which can be determined by turning the equipment off and on, the user 

is encouraged to try to correct the interference by one or more of the following measures:
  Reorient or relocate the receiving antenna.

  Increase the separation between the equipment and receiver.

  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

  Consult the dealer or an experienced radio/TV technician for help.

Содержание PM2/E













Отзывы: