• 2-Way Coaxial Dynamic Driver Design
• Propulsion Drive Flux-Cycle Motor System
• Wide-Angle Sound Dispersion Diaphragm
• Image Enhancing Wave Array Grill
• Complete Marine Weather Protection Components
• Corrosion Free One-Piece ABS Full Frame Basket
• Element Protection Treated PP Injection Cone
• UV/Salt Water Repellent Suspension System
• NBR Treated Rubber Surround
• Treated Linear Nomex Damper
• High-Strength Kapton Former with KSV Voice Coil
• Direct 13mm High Frequency PEI Driver
• Balance-Dome Tweeter with Neodymium Magnet
Congratulations on your purchase of an Elux Series product from VM Audio.
You have seen that with years of acquired taste for quality, the Elux Series has
the right design and performance to satisfy your utmost demand. With music
so clear and rich and bass so low and loud, you will be immersed in a world of
musical euphoria that anything else will seem like white noise. By following the
installation instructions carefully, you will ensure yourself performance that will
be enjoyed from each use for years to come. Reward yourself with the finer
things in life.
INTRODUCTION
• Coaxial Speaker System (2 pieces)
• Woofer Grilles (2 pieces - attached to speaker)
• Phillips-Head Stainless Steel Screws (4 pieces)
• Stainless Steel Washers (4 pieces)
• Mounting Template
INSIDE PACKAGE
FEATURES
Woofer
Tweeter
Power (RMS)
Power (Peak)
Frequency Response
Sensitivity
Nominal Impedance
(A) Trim Ring Diameter
(B) Trim Ring Height
(C) Mounting Diameter
(D) Mounting Depth
...................................
...................................
...................................
...................................
...................................
...................................
...................................
...................................
...................................
...................................
...................................
6.5 in. (165mm)
1/2 in. (13mm)
125 Watts
250 Watts
60Hz - 20kHz
90
4 ohms
7.68 in. (195mm)
1.10 in. (28mm)
5.59 in. (142mm)
2.52 in. (64mm)
SPECIFICATIONS
• Always disconnect the main power source or battery system before any
electrical installation is performed.
• Before drilling and inserting any screws or making any type of cutouts; ensure
there is enough clearance behind the speaker panel. Be aware of gas tanks,
fuel or hydraulic lines and electrical wires that may be located behind the
panel you will be working on, and make sure to not cut or drill through these
obstacles.
• If existing speaker wires are being replaced or new ones are being installed,
run all wires first before mounting the speakers.
• Avoid running wires through sharp corners and edges. Always use rubber
grommets to prevent wires from exposing and causing an electrical short
circuit.
• Be certain that the speakers are mounted firmly and secure on the panel. If
they are not firmly secured, the speakers can become a dangerous projectile
in a collision and cause severe injury.
• Although these speakers are designed to withstand the harsh marine
environment, they are not waterproof and should not be submerged under
water.
• Failure to connect the speakers as shown will result in damage to the
speakers which will not be covered under warranty.
INSTALLATION CONSIDERATIONS
INSTALLATION PROCEDURES
1.
Determine the mounting
location for the speaker and
mark the cutout circle and
screw holes using the template
provided.
2.
Carefully make the cutout
circle using the appropriate
tool for the panel material.
3.
Drill the screw holes with
an electric drill using 1/8” bit.
4.
Pull the speaker wires
through the cutout circle and
connect them to the terminals.
The positive terminal is marked
with a “+” and negative with “-”.
5.
Mount the speaker into the
cutout circle and secure the
speaker using four screws,
each one around every other
slot on the speaker frame.
+
(A)
(B)
(C)
(D)
