background image

The PORTA 

II

 / MINI PORTA altazimuth mount 

and tripod box contains the parts listed below.  
Make sure that your shipment contains all the 
parts.

For contents other than the above parts (instruments 

such as optical tubes), refer to a list on a facing page. 

Contents of the PORTA 

II

 / MINI PORTA

PORTA 

II 

/ MINI PORTA Mount and Aluminum 

Tripod Legs Set
4mm Allen Wrench(PORTA 

II

) / 5mm Allen Wrench(MINI PORTA)

3/16”Allen Wrench(PORTA 

II

) / 6mm Allen Wrench(MINI PORTA)

Altitude/Azimuth Slow Motion Handles  
Accessory Tray
Instruction Manual (This booklet.)

Parts List

Parts Descriptions

Shown PORTA 

II

Mount with Tripod 

Altitude/Azimuth 

Slow Motion Handles 

Allen Wrench

(for attaching the dovetail block)

Smaller Allen Wrench 

(for adjusting tension 

of altitude/azimuth motion)

Allen Wrench

(for attaching the dovetail block)

Smaller Allen Wrench 

(for adjusting tension 

of altitude/azimuth motion)

Accessory Tray

PORTA 

II

 A80Mf telescope shown, 

your telescope may differ

R130Sf telescope shown

R130Sf telescope shown

Dovetail Lock knob

Altitude Slow Motion Handle

Finder Scope

Finder Bracket

Eyepiece 

Diagonal Prism

Focus Knob

Tripod Leg Base

Tripod Leg

Tripod Leg Spreader 

Accessory Tray

Tray Lock Knob

Leg Extension Clamp

Dew Shield

Objective Lens (Inside)

Tube Ring Lock Screw

Optical Tube

Tube Ring

Before Use

Before Use

Eyepiece 

Eyepiece 

Focus Knob

Focus Knob

Finder Scope

Finder Scope

Safety Screw

Dovetail Mounting Block

Azimuth Slow Motion Handle

Safety Screw

Dovetail Mounting Block

Azimuth Slow Motion Handle

4

Содержание MINI PORTA

















Отзывы: