Vivid VFS5110SM Скачать руководство пользователя страница 17

S T A N D A R D   M O T I O N   S E R I E S   |   m a i n t e n a n c e   &   s a f e t y

1 7

Important Information

»  

Read and understand all instructions before installing and using the 

projection screen.

»  

Always connect this projection screen to a grounded outlet. The power 

outlet should be located near the screen and shall be easily accessible.

»  

This equipment must be supplied from a power system providing a 

PROTECTIVE EARTH connection and having a neutral connection, which 

can be reliably identified. 

»  

Always ensure that the unit is properly earthed and power connections 

correctly made. 

»  

To reduce the risk of electric shock, do not disassemble this projection 

screen, but take it to a qualified serviceman when service or repair is 

required. Incorrect reassembly can result in electric shock when used. 

»  

Close supervision is necessary when projection screen is in use by or 

near children. Do not leave screen unattended while is use. 

»  

Installer must ensure that the mounting structures and fasteners must 

be of adequate strength to securely support the screen so that 

vibrations or even abusive pulling on the screen surface will not cause 

the housing to work loose or fall. 

»  

Do not operate screen with a damaged cord or if the screen has been 

dropped or damaged until it has been examined and repaired by a 

qualified serviceman.

»  

Do not place or attach anything to metal casing or viewing surface of 

the screen. 

»  

Position cord so that it will not be tripped over, pulled or in contact 

with hot surfaces. 

»  

Do not plug the cord in with wet hands; electric shock could occur. 

»  

Save these instructions.

Product specifications are subject to change without notice

Specifications

Model No.

Screen Size

Screen Material

Screen Finish

Frame Material

Aspect Ratio

Gain

View Angle

Cleanable Screen

Fire Resistant

Motor (Power)

Weight

Warranty

VFS5110SM

110 in.

PVC/Fiberglass

Matte White

White Aluminum Alloy

16:9

1.0

170°

Yes

Yes

110V / 0.96A

34.1 lbs

2 year

VFS5120SM

120 in.

PVC/Fiberglass

Matte White

White Aluminum Alloy

16:9

1.0

170°

Yes

Yes

110V / 0.85A

44.75 lbs

2 year

VFS5133SM

133 in.

PVC/Fiberglass

Matte White

White Aluminum Alloy

16:10

1.0

170°

Yes

Yes

110V / 0.85A

60.96 lbs

2 year

Содержание VFS5110SM



















Отзывы: