Vitek VT-8514, Инструкция по эксплуатации, Страница: 5 / 24

5
ENGLISH
Note: The blender will not switch on if the
blender bowl (3) is installed incorrectly.
•
Use the operation mode switch (6) to
set the required rotation speed of the
knives:
–
«1» – (low speed) – for mixing liquid
foods.
–
«2» – (high speed) – for liquid and hard
foods.
–
«P» – pulse mode
• To switch the pulse mode on, set the
switch (6) to the position “P” and hold it
for several seconds.
•
During the operation or between the oper-
ation cycles, you can add the required
ingredients into the bowl (3). To do this,
remove the measuring cup (1) from the
lid (2). After adding ingredients through
the lid (2) opening, install the measuring
cup (1) back to its place.
• After the unit operation is finished, set the
operation mode switch (6) to the «0» posi-
tion and unplug the unit.
•
Remove the blender bowl (3) from the
motor unit (5) by turning it counterclock-
wise «
».
• Remove the lid (2) from the bowl (3).
• Take the processed food out of the
bowl (3).
•
After the operation is finished, wash the
blender bowl (3).
Note: - If food processing is hindered, you
can add some water, liquor or juice into the
blender bowl (3).
ATTENTION! Continuous operation time of
the blender should not exceed 3 minutes;
then switch the unit off and let it cool down
to room temperature for at least 10 min-
utes.
CLEANING AND CARE
After the unit operation is finished, switch the
blender off by setting the operation mode
switch (6) to the “0” position and unplug
it, remove the blender bowl (3) from the
motor unit (5) as described in the chapter
“USING THE BLENDER”. Take the pro-
cessed food out of the bowl (3).
•
Pre-wash the bowl (3). To do this, install
the blender bowl (3) on the motor unit
(5) and turn it clockwise «
». Add some
soap solution into the bowl (3). Cover the
bowl (3) with the lid (2) with installed mea-
suring cup (1). Insert the power plug into
the mains socket. Set the switch (6) to the
position “P” and hold it for several sec-
onds. After that set the switch (6) to the
position “0” and unplug the unit.
•
Remove the blender bowl (3) from the
motor unit (5) by turning it counterclock-
wise «
».
• Remove the lid (2) from the bowl (3).
• Pour out the soap solution from the bowl
(3) and rinse the bowl (3).
•
Wash the measuring cup (1), the lid (2)
and the bowl (3) with warm water add-
ing some soft detergent, then rinse them
and dry.
• Clean the motor unit (5) with a soft, slightly
damp cloth and then wipe it dry.
•
Do not use coarse sponges, abrasives and
solvents to clean the blender.
• Do not immerse the blender motor unit (5)
into any liquids; do not wash it in a dish-
washing machine.
•
Do not put the removable parts (1, 2, 3)
of the blender in a dishwashing machine.
STORAGE
• Perform the requirements of the
CLEANING AND CARE section before tak-
ing the unit away for storage.
•
Keep the unit out of reach of children and
people with disabilities.
DELIVERY SET
Table blender – 1 pc.
Manual – 1 pc.
TECHNICAL SPECIFICATIONS
Power supply: 220–240 V ~ 50 Hz
Rated input power: 350 W
Max power: 800 W
Bowl capacity: 1.2 L
IM VT-8514.indd 5 01.11.2018 17:15:38