Vitek VT-8510, Инструкция по эксплуатации, Страница: 4 / 24

4
ENGLISH
Attention! Do not allow children to play with
polyethylene bags or packaging film. Danger
of suffocation!
• Check the power cord and the power plug
periodically: they shouldn’t have any dam-
ages.
•
If the power cord is damaged, it should be
replaced by the manufacturer, a mainte-
nance service or similar qualified personnel
to avoid danger.
• Do not use the unit if the motor unit body, the
power cord or the plug is damaged, if the unit
works improperly or after it was dropped.
•
Do not attempt to repair the unit. Do not dis-
assemble the unit by yourself, if any mal-
function is detected or after it was dropped,
unplug the unit and contact any authorized
service center from the contact address list
given in the warranty certificate and on the
website www.vitek.ru.
•
To avoid damages, transport the unit in the
original packaging only.
• Keep the unit out of reach of children and
people with disabilities.
THE UNIT IS INTENDED FOR HOUSEHOLD USE
ONLY, ITS COMMERCIAL USAGE AND USAGE
IN PRODUCTION AREAS AND WORK SPACES
IS PROHIBITED.
BEFORE THE FIRST USE
After unit transportation or storage at low
temperature keep it for at least three hours
at room temperature before switching on
.
• Unpack the unit completely and remove any
stickers that can prevent unit operation.
• Check the unit for damages, do not use it in
case of damages.
• Before switching the unit on, make sure that
your home mains voltage corresponds to the
unit operating voltage.
• Before the first use wash all the removable
parts (1, 2, 3) with warm water and neutral
detergent and then dry thoroughly.
• Clean the motor unit (6) with a soft, slightly
damp cloth and then wipe it dry.
•
Do not immerse the motor unit (6) into
any liquids and do not wash it with
water.
• Place the blender only on a flat steady sur-
face.
ATTENTION! Continuous operation time of
the blender should not exceed 1 minute; then
switch the unit off and let it cool down to room
temperature for at least 5 minutes.
• Do not remove the blender bowl and the bowl
lid during the operation.
USING THE BLENDER
• Install the blender bowl (3) on the motor
unit (6), to do this take the bowl (3) by the
handle with your right hand, install the bowl
(3) on the motor unit (6) and turn the bowl (3)
clockwise until it is fixed.
•
Put the necessary ingredients into the
bowl (3).
• Install the lid (2) into the bowl (3).
• Insert the measuring cup (1) in the lid (2)
opening and turn it counterclockwise until
it is fixed.
Notes:
–
Before starting to chop/mix, we recommend
to peel fruit, remove inedible parts, such
as stones, and cut fruit into cubes approxi-
mately 2х2 cm in size.
–
The blender is not intended for beating eggs,
making potato mash, kneading dough,
extracting fruit or vegetable juice, chopping
hard or frozen products, chopping meat and
meat products.
–
The amount of foodstuffs to be processed
should not exceed 2/3 of the capacity of
the bowl in which they are processed or be
below the minimal “250” mark of the blender
bowl.
–
For easy control of the amount of the pro-
cessed food there are liquid scales on two
sides of the blender bowl.
• Make sure once again that the blender bowl
(3) is installed correctly and is fixed.
•
Insert the power plug into the mains socket.
Note: The blender will not be switched on if the
blender bowl (3) is installed incorrectly.
• Use the operation mode switch (7) to set the
required rotation speed of the knives:
–
«1» (low speed) – for mixing liquid prod-
ucts.
–
«2» – mixing products.
–
«3» – mixing and chopping.
–
«4» (high speed) – for liquid and hard
products.
–
«P» – pulse mode
IM VT-8510.indd 4 06.03.2019 14:20:23