2
DE2061
3.2 Coding
All WT-201 units have an 8-key
DIP switch (marked 1 to 8).
Each switch may be set to ON
or OFF position, to create a
unique digital system code -
see Figure 4.
Figure 4.
Code Selector
Use a ball point pen to set each of the switches to match the
code setting of the companion receiver.
CAUTION:
The factory test code (2, 4, 5, 6, 7 ON / 1, 3, 8 OFF)
must not be used. Also avoid codes which are often OFF or
alternating ON/OFF used: all keys ON, all keys settings.
3.3 Channel Selection
(WT-201A only)
Model WT-201A is equipped with
a 4-channel selector marked
CHAN (see Figure 5). Using this
switch you can set the transmitter
for activating one of four outputs
at the receiver. This feature is
important for zoning purposes -
Figure 5.
Channel Selector
activating different alarm zones of a control panel via a
companion, multi-channel receiver. The channel data transmitted
by the WT-201A is selected by positioning the 4 switches in
accordance with the required channel number. Use a ball point
pen to set the channel selector as required by the host system.
3.4 Testing
A.
Stand 3 m (10 ft) away from the receiver and operate the
transmitter.
B.
Verify that the transmitter LED lights, indicating good battery
condition.
C.
Observe that the receiver LED lights, indicating detection of
the transmitted RF signal.
D.
Verify activation of the receiver's output relay associated with
the channel selected in the transmitter (the WT-201
single-channel transmitter operates the relay associated with
channel 1).
E.
Operate the transmitter from various locations within the area
covered by the receiver to determine "dead" locations, where
transmission is obstructed by walls and large objects, or
affected by structural materials.
3.5 Key-Ring Installation
A.
Remove the chain by opening and
slipping it through the triangle on
top of the WT-201.
B.
Insert the tip of a long-nose pliers
into the triangle and open it.
C.
Remove the triangle.
D.
Open the plastic bag which
contains the key-ring kit.
E.
Slip the key-ring triangle through
the last link of the key-ring chain
and install the triangle into the
hole on the top of the WT-201
(Figure 6).
Figure 6.
Key-Ring
Installation
F.
Using the pliers, close the key-ring triangle.
4
44
4.
. .
. MISCELLANEOUS COMMENTS
MISCELLANEOUS COMMENTS
MISCELLANEOUS COMMENTS
MISCELLANEOUS COMMENTS
4.1 Product Limitations
Our wireless systems are very reliable and are tested to high
standards. However, due to their low transmitting power (required
by FCC regulations) there are some limitations to be considered:
A.
Receivers may be blocked by radio signals on or near their
operating frequencies, regardless of the code selected.
B.
A receiver can respond to one transmitted signal at a time.
C.
Wireless equipment should be tested regularly (at least once
a week) to determine if there are sources of interference and
to protect against faults.
4.2 Compliance with Standards
WARNING: Changes or modifications to this unit not
expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
The 315 MHz model of this device complies with Part 15 of the
FCC Rules and RSS-210 of Industry and Science Canada.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device
must accept any interference that may be received, including
interference that may cause undesired operation.
This
device complies with the essential requirements and provisions of
Directive 1999/5/EC of the European Parliament and of the Council of
9
March
1999
on
radio
and
telecommunications
terminal
equipment.
4.3 Frequency Allocations for Wireless
Devices in European (EU) Countries
•
433.92 MHz
has no restriction in any EU member state.
•
418 MHz
is allowed in the UK only.
•
315 MHz
is not allowed in any EU member state
WARRANTY
WARRANTY
WARRANTY
WARRANTY
Visonic Ltd. and/or its subsidiaries and its affiliates ("the Manufacturer") warrants its
products hereinafter referred to as "the Product" or "Products" to be in conformance with
its own plans and specifications and to be free of defects in materials and workmanship
under normal use and service for a period of twelve months from the date of shipment by
the Manufacturer. The Manufacturer's obligations shall be limited within the warranty
period, at its option, to repair or replace the product or any part thereof. The Manufacturer
shall not be responsible for dismantling and/or reinstallation charges. To exercise the
warranty the product must be returned to the Manufacturer freight prepaid and insured.
This warranty does not apply in the following cases:
improper installation, misuse,
failure to follow installation and operating instructions, alteration, abuse, accident or
tampering, and repair by anyone other than the Manufacturer.
This warranty is exclusive and expressly in lieu of all other warranties, obligations or
liabilities, whether written, oral, express or implied, including any warranty of
merchantability or fitness for a particular purpose, or otherwise. In no case shall the
Manufacturer be liable to anyone for any consequential or incidental damages for breach
of this warranty or any other warranties whatsoever, as aforesaid.
This warranty shall not be modified, varied or extended, and the Manufacturer does not
authorize any person to act on its behalf in the modification, variation or extension of this
warranty. This warranty shall apply to the Product only. All products, accessories or
attachments of others used in conjunction with the Product, including batteries, shall be
covered solely by their own warranty, if any. The Manufacturer shall not be liable for any
damage or loss whatsoever, whether directly, indirectly, incidentally, consequentially or
otherwise, caused by the malfunction of the Product due to products, accessories, or
attachments of others, including batteries, used in conjunction with the Products.
The Manufacturer does not represent that its Product may not be compromised and/or
circumvented, or that the Product will prevent any death, personal and/or bodily injury
and/or damage to property resulting from burglary, robbery, fire or otherwise, or that the
Product will in all cases provide adequate warning or protection. User understands that a
properly installed and maintained alarm may only reduce the risk of events such as
burglary, robbery, and fire without warning, but it is not insurance or a guarantee that
such will not occur or that there will be no death, personal damage and/or damage to
property as a result.
The Manufacturer shall have no liability for any deat, personal and/or bodily injury
and/or damage to property or other loss whether direct, indirect, incidental,
consequential or otherwise, based on a claim that the Product failed to function.
However, if the Manufacturer is held liable, whether directly or indirectly, for any loss or
damage arising under this limited warranty or otherwise, regardless of cause or origin, the
Manufacturer's maximum liability shall not in any case exceed the purchase price of the
Product, which shall be fixed as liquidated damages and not as a penalty, and shall be
the complete and exclusive remedy against the Manufacturer.
Warning:
The user should follow the installation and operation instructions and among
other things test the Product and the whole system at least once a week. For various
reasons, including, but not limited to, changes in environmental conditions, electric or
electronic disruptions and tampering, the Product may not perform as expected. The user
is advised to take all necessary precautions for his/her safety and the protection of his/her
property.
6/91
VISONIC LTD. (ISRAEL):
P.O.B 22020 TEL-AVIV 61220 ISRAEL. PHONE: (972-3) 645-6789, FAX: (972-3) 645-6788
VISONIC INC. (U.S.A.):
10 NORTHWOOD DRIVE, BLOOMFIELD CT. 06002-1911. PHONE: (860) 243-0833, (800) 223-0020 FAX: (860) 242-8094
VISONIC LTD. (UK):
FRASER ROAD, PRIORY BUSINESS PARK, BEDFORD MK44 3WH. PHONE: (0870) 730-0800 FAX: (0870) 730-0801
INTERNET:
www.visonic.com
VISONIC LTD. 2001 WT-201 DE2061- (REV. 6, 5/01)